The escalating accumulation of polypropylene (PP) plastic waste poses significant environmental challenges, requiring innovative waste management strategies. Pyrolysis of plastic waste presents a promising approach for sustainable production of alternative fuels. However, pyrolysis oil possesses...
A combination of wet torrefaction and binderless briquetting processes, namely torre-briquetting process, has been developed in Indonesia to treat the mixed municipal solid waste into a solid fuel. A mixture of organic and plastic waste was treated in a 2.5 L reactor using saturated steam in the temperature range of 175 to 225°C. Afterwards, the products were briquetted in varied pressure of 500 to 1000 bar. It was observed that the wet torrefaction process at the temperature of 225°C, residence time of 30 min and sample-to-water ratio of 1:2.5 was able to produce the solid product with heating value of up to 5923 kcal/kg, equivalent to that of bituminous coal. In the briquetting aspect, the briquetted product showed adequate drop test durability of 90% at 1000 bar briquetting pressure. The density of the briquette however, has not reached the standard of 1000 kg/m3, presumably due to the presence of large sized plastic in the briquette. The results suggest that by employing wet torrefaction, the organic fibers in the mixed waste are trapped into the plastic matrix, producing granules which are suitable for briquetting. Therefore, the torre-briquetting process can be a revolutionary solution to treat the MSW without any separation required to produce high caloric solid fuel.
Preliminary survey showed that organic waste from the market is about 18.77%, or second largest in the total waste generation. Its management becomes a challenge, because it is not comprised only of organics but also mixed with small amount of plastics; therefore, conventional biological process will not achieve their maximum efficiency. Wet torrefaction is a thermal process in hot water medium, which will dissolve organic materials into water, effectively converting most solids into liquid product. Banana fruit stem and cabbage were chosen as the mixed organic waste representative, and treated in a 2.5 L reactor using saturated steam in the temperature range of 175 to 225 °C before being analyzed for their heating value in solid products as fuel precursors, and their nitrogen, phosphorus and potassium (NPK) contents in liquid products as liquid fertilizer precursors. It was found that for cabbage, the wet torrefaction process at 200 °C and 90 min resulted in 15.59 MJ/kg product heating value with NPK content of 3.43%. For banana fruit bunch stem, the wet torrefaction process at 225 °C and 30 min resulted in 17.64 MJ/kg product heating value with NPK content of 5.13%. It can be concluded that wet torrefaction process can simultaneously produce solid and liquid product as solid fuel and liquid fertilizer, respectively.
As an archipelago country, electrification in Indonesia is still limited in the main islands and has not reached the remote and outer islands due to the limited infrastructure of the country. To provide the electricity in the region, the small generator set is needed. However, the usage of the diesel fueled engine in the generator set is predicted to be more difficult in the future due to the fossil fuel price and rareness. The Stirling Engine offers the solution for such problem since it is able to utilize various type of fuel as energy sources. In this research, the further study was conducted on the performance of the 200-Watt Stirling engine’s furnace to provide the heat source. The type of furnace used in the stirling engine system is called Rocket Stove. The fuel used in this research was bamboo as one of the biomasses with enormous potential in the country. The numerical simulation was conducted to estimate the mass flow rate of the fuel. The experiment was conducted to obtain the rocket stove temperature distribution. Evaluation was then conducted to analyze the performance of the heat exchanger absorbing the heat of the flue gas. The results obtained from this research were the fuel rate required to produce sufficient heat to meet the heat requirement of Stirling Engine was 3.28 kg/h in bamboo and 1.43 kg/h in LPG. The average temperature distribution before the Heat Exchanger reached 788 ℃ with the standard deviation of 61 °C on the bamboo and the average temperature distribution before the Heat Exchanger reached 725 °C with the standard deviation of 3 °C on LPG. The effectiveness of heat exchanger used is 68%.
1 May 2017 in IOP Conference Series: Earth and Environmental Science
Energy use has increased steadily over the last century due to population and industry increase. With the growing of GHG, biomass becomes an essential contributor to the world energy need. Indonesia is the third rice producer in the world. Rice straw has been converted to solid fuel by Hydrothermal Treatment (HT) for electricity generation. HT is a boiling solid organic or inorganic substance in water at high pressure and temperature within a holding time. HT converts high moisture content biomass into dried, uniform, pulverized, and higher energy density solid fuels. HT can effectively transport nutrient components in biomass into a liquid product known as fertilizer. This paper deals with an evaluation of hydrothermal treatment of rice straw for solid fuel and liquid fertilizer. An investigation of rice straw characteristics were completed for Bandung rice straw with various condition of temperature, biomass-water ratio, and holding time in the purpose to find the changes of calorific value for solid product and (N, P, K, and pH) for liquid product. The results showed that solid product at 225 °C and 90 min consists in a heating value 13.8 MJ/kg equal to lignite B. Liquid product at 225 °C and 90 min had the NPK content similar to that of micronutrients compound liquid fertilizer. The dried solid product should be useful for Coal Fire Power Plant, and the liquid product is suitable for plants. This research proves that hydrothermal process can be applied to rice straw to produce solid fuel and liquid fertilizer with adequate quality.