In this article, amino functionalized multiwalled carbon nanotubes (MWCNTs) were prepared by chemical modification of the surface of a MWCNTs using γ-aminopropyltriethoxysilane (APTES) and dispersed into the epoxy composition. The modifying agent (APTES) was directly deposited on the MWCNTs surfaces. For the functionalization of MWCNTs, was used not the APTES concentrate, as it had been described in previous works, but its freshly prepared aqueous solution. Properties of APTES-treated MWCNTs were characterized by transmission electron microscope (TEM), Raman spectroscopy and FT-IR. The results showed that the functionalization and chemical compatibility of APTES-treated MWCNTs with epoxy composition provides their best dispersion in the epoxy composition, had important influence on curing behavior, structure and physicochemical properties of the epoxy composites plasticized with trichloroethyl phosphate. The results showed that the functionalization and chemical compatibility of APTES-treated MWCNTs with epoxy composition provides increased of physicomechanical properties of epoxy composites: bending stress increases by 194% and bending modulus increases by 137%, the tensile strength increases by 108% and the tensile elastic modulus increases by 52%, impact strength increases by 300%, in comparison with plasticized epoxy composite that does not contain MWCNTs.
1 March 2016 in Protection of Metals and Physical Chemistry of Surfaces
The electrochemical method for synthesizing multilayer graphene oxide by the anodic oxidation of disperse graphite in sulfuric acid is proposed. The possibility of sequential dispersion of graphite in the course of its electrochemical oxidation, hydrolysis, and thermolysis is demonstrated. It is shown that the resulting nanostructured materials tend to form agglomerates in aqueous dispersions. When treated with supersonic, the size of oxidized graphite particles decreases noticeably and they form multilayer graphene oxide. Thermolysis (250°С) leads to a considerable expansion of oxidized graphite particles (the inflation coefficient 1490 cm3 g–1) and reduction of oxygen-containing functional groups. The structure of thus obtained material includes polygraphene sheets with the thickness of 0.01–0.1 µm and contains pores of 1–10 µm.
1 May 2009 in Protection of Metals and Physical Chemistry of Surfaces
Results of studies in the field of electrochemical composition coatings (ECC) are presented. Methods of synthesis, functional properties, and structural peculiarities of the main types of ECC are considered.
1 May 2017 in Protection of Metals and Physical Chemistry of Surfaces
Composite electrochemical coatings (CECs) based on nickel and fullerene C60 as the dispersed phase are obtained. The process of electrodeposition of these coatings is studied. The method of secondary ion-mass spectrometry was used to determine the composition of nickel–fullerene C60 CECs. It is found that coefficients of sliding friction of the obtained CECs decrease by from 1.8 to 2.5 times as compared to similar nickel coatings with no dispersed phase. Corrosion behavior of nickel–fullerene C60 CECs is studied in 0.5M H2SO4 solution.
Composite electrochemical coatings (CECs) on the basis of nickel modified with multilayer graphene oxide (GO) were deposited from a sulfate–chloride electrolyte in pulsed electrolysis mode. The microstructure of these CECs was studied by X-ray phase analysis and scanning electron microscopy. It was found that the microhardness of nickel–GO CECs increases by approximately 1.40 times compared to pure nickel. The corrosion–electrochemical behavior of nickel–GO composite coatings in 0.5 M H2SO4 was studied. Based on tests in 3.5% NaCl, it was found that the addition of graphene oxide particles into the matrix of nickel electrodeposits, increases their corrosion resistance by 1.40–1.50 times. This can be explained by the uniformity of the distribution of GO in the nickel matrix, which contributes to the reduction in grain size, as well as the impermeability and stability of graphene oxide.