Composite electrochemical coatings (CECs) on the basis of nickel modified with multilayer graphene oxide (GO) were deposited from a sulfate–chloride electrolyte in pulsed electrolysis mode. The microstructure of these CECs was studied by X-ray phase analysis and scanning electron microscopy. It was found that the microhardness of nickel–GO CECs increases by approximately 1.40 times compared to pure nickel. The corrosion–electrochemical behavior of nickel–GO composite coatings in 0.5 M H2SO4 was studied. Based on tests in 3.5% NaCl, it was found that the addition of graphene oxide particles into the matrix of nickel electrodeposits, increases their corrosion resistance by 1.40–1.50 times. This can be explained by the uniformity of the distribution of GO in the nickel matrix, which contributes to the reduction in grain size, as well as the impermeability and stability of graphene oxide.
In this work we have synthesized Ti3C2TX MXene powder and studied its structure. Composite electrochemical coatings (CECs) of Ni-Ti3C2TX MXene were obtained from a sulfate– chloride bath in the galvanostatic regime. The microstructure of CEC was researched using X-ray phase analysis and scanning electron microscopy methods. It has been established that a Ni–Ti3C2TX MXene CEC microhardness rises by about 1.80 times compared with electrolytic Ni without a dispersed phase. For corrosion research, different corrosive media is applied. The corrosion–electrochemical behavior of Ni–Ti3C2TX MXene CECs by the chronovoltamperometry method in 0.5 M H2SO4 solution has been investigated. Trials in 3.5% NaCl have shown that Ti3C2TX MXene inclusion into the matrix of the electrochemical Ni results in a decrease in the corrosion rate by 1.60–1.75 times. These effects are due to the addition of Ti3C2TX MXene into the nickel matrix and the formation of CECs with a strengthening fine-grained structure.
Within the framework of this study, Ni-based composite electrochemical coatings (CECs) modified with multilayer graphene oxide (GO) processed using microwave radiation have been deposited. The process of these coatings’ electrodeposition in the potentiodynamic mode has been studied. The structure of Ni–GO and Ni–GO (MW) CECs has been studied using X-ray phase analysis (XPA) and scanning electron microscopy (SEM).It has been shown that the addition of GO into a nickel deposit contributes to the formation of uniform fine-grained coatings. As a result, the microhardness of the Ni–GO (MW) CECs increases by 1.40 times compared to Ni without GO. The corrosion–electrochemical behavior of nickel CECs in 0.5 M H2SO4 solution was researched. It was established that the corrosion rate of the nickel–GO (MW) CEC in 3.5% NaCl decreases by about 1.70 times in contrast to unmodified nickel coatings. This effect is due to the absence of agglomeration of the graphene oxide in the volume of the nickel matrix and the impermeability of GO particles to the corrosive environment.
Electrodeposited nickel-based composite coatings are widely used for corrosion protection and wear resistance in engineering applications. Here, Ni–Ti3C2Tx composite coatings were fabricated from a Watts-type electrolyte containing a stable colloidal solution of predominantly single-layer Ti3C2Tx MXene nanosheets (2 mg·mL−1). The effect of MXene incorporation on electrodeposition behavior, crystallographic structure, surface morphology, microhardness, and corrosion performance was systematically investigated. X-ray diffraction and electron microscopy revealed that Ti3C2Tx nanosheets induce preferential growth along the Ni(200) plane and promote crystallite refinement, leading to a denser and more uniform coating. As a result, microhardness increased by 2.2–2.4 times compared with pure nickel, while corrosion rates in 3.5 wt.% NaCl decreased by 1.75–1.85 times. The enhanced functional properties are attributed to the synergistic effects of crystallographic orientation control, grain size refinement, and the barrier effect of delaminated MXene nanosheets. These findings demonstrate that single-layer Ti3C2Tx MXene is an effective reinforcing phase for nickel-based electrodeposited coatings, offering a straightforward approach to simultaneously optimizing mechanical and corrosion performances for advanced surface engineering applications.
In this study, a method for producing nitrogen-modified graphene oxide (NMGO) using hydrothermal synthesis in the presence of triethanolamine is presented. The composition and structure of NMGO are characterized using X-ray phase analysis (XPA), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy, and Raman spectroscopy. Ni-based metal matrix coatings (MMCs) modified with NMGO were obtained from a sulfate-chloride electrolyte in the galvanostatic mode. The process of electrochemical deposition of these coatings was studied using chronovoltammetry. The microstructure of Ni–NMGO MMCs was studied using the XPA and SEM methods. It has been established that the addition of NMGO particles into the Ni matrix results in an increase in the microhardness of the resulting coatings by an average of 1.30 times. This effect is a consequence of the refinement of crystallites and high mechanical properties of NMGO phase. The corrosion-electrochemical behavior of studied electrochemical deposits in 0.5 M sulfuric acid was analyzed. It has been shown that the corrosion rate of Ni–NMGO MMCs in a 3.5% sodium chloride environment decreases by approximately 1.50–1.70 times as compared to unmodified Ni coatings. This is due to NMGO particles that act as a barrier preventing the propagation of the corrosion and form corrosive galvanic microelements with Ni, promoting anodic polarization.