Carlos Eduardo Pardo García

Prof. Dr. Carlos Eduardo Pardo García

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 April 2022 in Lubricants
Verified
Journal Article
Open access
PDF file
CGCarlos Eduardo Pardo García
Carlos Eduardo Pardo García
SASofia Orjuela Abril
Sofia Orjuela Abril
JLJhon Pabón León
Jhon Pabón León
Hydrogen is considered one of the main gaseous fuels due to its ability to improve thermal performance in diesel engines. However, its influence on the characteristics of lubricating oil is generally ignored. Thus, in the present investigation, an analysis of the effect on the physical and chemical properties of lubricating oil with mixtures of diesel fuel–hydrogen was carried out, and the environmental impacts of this type of mixture were assessed. The development of the research was carried out using a diesel engine under four torque conditions (80 Nm, 120 Nm, 160 Nm and 200 Nm) and three hydrogen gas flow conditions (0.75 lpm, 1.00 lpm and 1.25 lpm). From the results, it was possible to demonstrate that the presence of hydrogen caused decreases of 3.50%, 6.79% and 4.42% in the emissions of CO, HC, and smoke opacity, respectively. However, hydrogen further decreased the viscosity of the lubricating oil by 26%. Additionally, hydrogen gas produced increases of 17.7%, 29.27%, 21.95% and 27.41% in metallic components, such as Fe, Cu, Al and Cr, respectively. In general, hydrogen favors the contamination and oxidation of lubricating oil, which implies a greater wear of the engine components. Due to the significantly negative impact of hydrogen on the lubrication system, it should be considered due to its influence on the economic and environmental cost during the engine’s life cycle.

2 March 2021 in Lubricants
Verified
Journal Article
Open access
PDF file
Brando HernándezBrando Hernández
Brando Hernández
Daniel Maestre-CambronelDaniel Maestre-Cambronel
Daniel Maestre-Cambronel
CGCarlos Eduardo Pardo García
Carlos Eduardo Pardo García
MFMarlen Del Socorro Fonseca-Vigoya
Marlen Del Socorro Fonseca-Vigoya
JLJhon Pabón León
Jhon Pabón León
Internal combustion engines are widely implemented in several applications; however, they still face significant challenges due to the sealing capacity of the compression rings. Gas leakage through the crankcase, also known as blow-by, directly impacts power losses, overall efficiency, and global emissions. Therefore, the present study investigates the influence of parameters such as the ring gap, ring masses, and twist angle of the compression rings on the sealing capacity of the combustion chamber. A mathematical model is proposed to account for geometric, dynamic, and operational characteristics in a single-cylinder diesel engine. The results indicated that the greatest gas losses to the crankcase occur during the compression and combustion stages as a consequence of extreme pressure conditions. Specifically, at least 0.5% of the gases locked in the combustion chamber are released on each cycle, while increasing the mass of the compression rings boosts the gas leakage due to higher inertial forces in the rings. In contrast, a positive twist angle of the compression rings reduced the combustion gases leakage by 7.33×10−5 g/cycle. Additionally, a combined reduction in the gap of both compression rings minimized the leakage flows by 37%. In conclusion, the proposed model served as a robust tool to evaluate different parameters on the sealing capacity of the combustion chamber that contribute to minimizing global emissions. Secondary piston motion and ring distortion represent significant opportunities in future studies.

9 April 2021 in Lubricants
Verified
Journal Article
Open access
PDF file
CGCarlos Eduardo Pardo García
Carlos Eduardo Pardo García
JSJhan Piero Rojas Suárez
Jhan Piero Rojas Suárez
SASofia Orjuela Abril
Sofia Orjuela Abril
In the present work, a numerical model is developed to investigate the influence of wear and misalignment on the bearings of a stationary diesel engine. The model implemented considers the effects of surface wear on the bearing, cavitation effects, and surface roughness. For the numerical analysis, changes in the surface roughness of σμσ=0.75 μm, σμσ=1 μm, and σμσ=1.25 μm are defined, and changes in the bearing load of 50%, 75%, and 100%. The results demonstrated that increasing the surface roughness intensifies the bearing wear, which represents 18% and 140% of the bearing clearance for the roughness of σμσ=1 μm and σμσ=1.25 μm, respectively. Additionally, the surface roughness causes a considerable increase in the bearing wear rate. The results described a maximum wear rate of μ20 μm/s. In general, increasing the bearing load by 25% doubles the hydrodynamic pressure conditions increases friction force by 33%, and reduces lubrication film thickness by 12%. The analysis of the angle of deflection, ϕx and ϕy, shows that the moment and the degree of misalignment tend to increase significantly with the increase in the magnitude of the angle ϕy. Negative angles of deflection, ϕx, produce a greater increase in the degree of misalignment and the moment. This implies a greater chance of contact with the bearing surface. In conclusion, the proposed methodology serves as a reliable tool to simultaneously evaluate key parameters on the tribological behavior of bearings that further extend their endurance and minimize wear damage.

7 April 2022 in Lubricants
Verified
Journal Article
Open access
PDF file
SASofia Orjuela Abril
Sofia Orjuela Abril
MFMarlen Del Socorro Fonseca-Vigoya
Marlen Del Socorro Fonseca-Vigoya
CGCarlos Eduardo Pardo García
Carlos Eduardo Pardo García
In the present investigation, a study is carried out using numerical simulation on the effects of cylinder deactivation on tribological parameters and emissions in an internal combustion engine. For the development of the research, a tribological model was used to predict the characteristics of the lubrication film, friction conditions, blow-by gas, and deformation of the piston rings. Additionally, the construction of a CFD model was carried out to describe the kinematic movement of the engine piston. The analysis of results allowed for the demonstration of the active cylinders presenting an increase of 21.53% and 7.65% in the pressure and temperature in the cylinder wall. Additionally, the active cylinders present a reduction of 11.33% in the minimum thickness of the lubrication film and an increase in the friction force due to asperities, which implies an increase of 33% in power losses due to friction. The implementation of technologies such as cylinder deactivation causes an increase in combustion gas leaks caused by the increase in pressure of the active cylinders. However, the use of this technology allows reducing 9.09%, 8.26%, and 7.41% in CO, HC, and NO emissions. Although the use of technologies such as cylinder deactivation allows significant fuel savings, it is necessary to consider the negative effects caused by this technology, such as the increase in combustion gas leaks and the increase in power loss by the greatest frictional forces.

18 February 2021 in Lubricants
Verified
Journal Article
Open access
PDF file
SASofia Orjuela Abril
Sofia Orjuela Abril
CGCarlos Eduardo Pardo García
Carlos Eduardo Pardo García
JLJhon Pabón León
Jhon Pabón León
Currently, internal combustion engines contribute to the problem of global warming due to their need to use products derived from fossil resources. To mitigate the above problem, this study proposes the use of coatings on the cylinder bore in order to reduce fuel consumption and polluting emissions. Therefore, in the present study a numerical model is developed in which the tribological behavior, heat fluxes, and leakage of the combustion gases in the chamber are considered to evaluate the influence of the coating. Nickel nanocomposite (NNC) and diamond-like carbon (DLC) coatings are considered in the study. The results demonstrate that the NNC coating produces a 32% reduction in the total friction force of the compression ring. The estimated maximum temperatures for the lubricating oil were 214, 202, and 194 °C for the DLC, steel, and NNC materials. Increasing the temperature in the DLC coating can cause a reduction in the tribological performance of the lubricant. The estimates made show that the implementation of the NNC coating allows a maximum reduction of 5.28 ton of fuel and 39.30 kg of CO emissions, which are based on the global fleet of diesel engines forecast for the year 2025 (corresponding to one hundred and eighty million engines) and a test time of 1800 s. The proposed numerical model allows future analyses to be carried out for other types of materials used as coatings. Additionally, the model can be expanded and adapted to consider other systems that involve friction processes in the engine.

6 May 2021 in Lubricants
Verified
Journal Article
Open access
PDF file
CGCarlos Eduardo Pardo García
Carlos Eduardo Pardo García
JSJhan Piero Rojas Suárez
Jhan Piero Rojas Suárez
SASofia Orjuela Abril
Sofia Orjuela Abril
The objective of the present investigation is to analyze the tribological performance between the union of the cylinder liner and the compression ring under the influence of surface texturing and different lubrication boundary conditions. The analysis is carried out by developing a numerical model, which involves hydrodynamic pressure, lubrication film thickness, textured surface, dynamic forces, and lubrication boundary conditions (starved lubrication and fully flooded lubrication). MATLAB® software (The MathWorks Inc., Natick, MA, USA) is used to solve the equations developed. The results show that the application of a textured surface on the cylinder liner allows obtaining a reduction of 20% and 5% in the asperity contact force and in the total friction force. Additionally, the textured surface allows for a 4% increase in MOFT. In this way, it is possible to reduce the power loss. The implementation of a boundary condition of fully flooded lubrication produces an overestimation in the total friction force due to the greater prominence of the lubrication film. Implementing a textured surface in the ring profile is an alternative way to reduce power loss. The results show that this alternative allows an 8% reduction in power loss.