Sofia Orjuela Abril

Prof. Sofia Orjuela Abril


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2022 in Heliyon
Verified
Journal Article
Open access
CGCarlos Pardo García
Carlos Pardo García
SASofia Orjuela Abril
Sofia Orjuela Abril
JLJhon Pabón León
Jhon Pabón León
Hydrogen is one of the main alternative fuels with the greatest potential to replace fossil fuels due to its renewable and environmentally friendly nature. Due to this, the present investigation aims to evaluate the combustion characteristics, performance parameters, emissions, and variations in the characteristics of the lubricating oil. The investigation was conducted in a spark-ignition engine fueled by gasoline and hydrogen gas. Four engine load conditions (25%, 50%, 75%, and 100%) and three hydrogen gas mass concentration conditions (3%, 6%, and 9%) were defined for the study. The investigation results allowed to demonstrate that the injection of hydrogen gas in the gasoline engine causes an increase of 3.2% and 4.0% in the maximum values of combustion pressure and heat release rates. Additionally, hydrogen causes a 2.9% increase in engine BTE. Hydrogen’s more efficient combustion process allowed for reducing CO, HC, and smoke opacity emissions. However, hydrogen gas causes an additional increase of 14.5% and 30.4% in reducing the kinematic viscosity and the total base number of the lubricating oil. In addition, there was evidence of an increase in the concentration of wear debris, such as Fe and Cu, which implies higher rates of wear in the engine’s internal components.

5 April 2022 in Lubricants
Verified
Journal Article
Open access
PDF file
CGCarlos Eduardo Pardo García
Carlos Eduardo Pardo García
SASofia Orjuela Abril
Sofia Orjuela Abril
JLJhon Pabón León
Jhon Pabón León
Hydrogen is considered one of the main gaseous fuels due to its ability to improve thermal performance in diesel engines. However, its influence on the characteristics of lubricating oil is generally ignored. Thus, in the present investigation, an analysis of the effect on the physical and chemical properties of lubricating oil with mixtures of diesel fuel–hydrogen was carried out, and the environmental impacts of this type of mixture were assessed. The development of the research was carried out using a diesel engine under four torque conditions (80 Nm, 120 Nm, 160 Nm and 200 Nm) and three hydrogen gas flow conditions (0.75 lpm, 1.00 lpm and 1.25 lpm). From the results, it was possible to demonstrate that the presence of hydrogen caused decreases of 3.50%, 6.79% and 4.42% in the emissions of CO, HC, and smoke opacity, respectively. However, hydrogen further decreased the viscosity of the lubricating oil by 26%. Additionally, hydrogen gas produced increases of 17.7%, 29.27%, 21.95% and 27.41% in metallic components, such as Fe, Cu, Al and Cr, respectively. In general, hydrogen favors the contamination and oxidation of lubricating oil, which implies a greater wear of the engine components. Due to the significantly negative impact of hydrogen on the lubrication system, it should be considered due to its influence on the economic and environmental cost during the engine’s life cycle.

3 December 2020 in Lubricants
Verified
Journal Article
Open access
PDF file
SASofia Orjuela Abril
Sofia Orjuela Abril
JSJhan Piero Rojas Suárez
Jhan Piero Rojas Suárez
EFE Flórez-Solano
E Flórez-Solano
The problem of climate change and the reduction of fossil fuels has motivated the development of research focused on improving the efficiency of internal combustion engines. This research proposes a methodology based on mathematical models to determine the energy losses caused by auxiliary systems and friction processes in the engine. Therefore, models are proposed for calculating the energy losses in fuel injection, lubrication, and cooling system. In the same way, models are proposed for the energy losses due to friction in the piston, valve train, and bearings. Experimental tests are carried out on a single-cylinder diesel engine under different operating conditions to validate the proposed models. The results showed that the energy losses of the fuel injection, lubrication, and coolant system are equal to 0.61%, 0.30%, and 0.31% of the chemical energy of the injected fuel. In the case of the energy losses by friction processes, the piston, valve train, and bearings represent 5.47%, 1.34%, and 1.85% of the fuel energy, respectively. Additionally, the proposed model allows estimating the minimum lubrication film present in the piston, valve train, and bearings, which in the particular case of the present study were 0.63 µm, 0.10 µm, and 0.57 µm, respectively. In general, the methodology developed in the present work stands as a robust tool to evaluate the modifications and/or designs of auxiliary systems and friction processes to reduce the energy losses and protect the system from wear caused by lubrication problems. Additionally, the methodology allows evaluating the effect of different types of fuels on the lubrication conditions of the piston and the crankshaft bearings.

18 May 2024 in Heliyon
Verified
Journal Article
Open access
SASofia Orjuela Abril
Sofia Orjuela Abril
ATAna Torregroza-Espinosa
Ana Torregroza-Espinosa
JDJorge Duarte-Forero
Jorge Duarte-Forero
This research proposes designing and implementing a system to produce hydrogen, utilizing the thermal energy from the exhaust gases in a natural gas engine. For the construction of the system, a thermoelectric generator was used to convert the thermal energy from the exhaust gases into electrical power and an electrolyzer bank to produce hydrogen. The system was evaluated using a natural gas engine, which operated at a constant speed (2400 rpm) and six load conditions (20 %, 40 %, 60 %, 80 %, and 100 %). The effect of hydrogen on the engine was evaluated with fuel mixtures (NG + 10 % HEF and NG + 15 % HEF). The results demonstrate that the NG + 10 % HEF and NG + 15 % HEF mixtures allow for a decrease of 1.84 % and 2.33 % in BSFC and an increase of 1.88 % and 2.38 % in BTE. Through the NG + 15 % HEF mixture, the engine achieved an energy efficiency of 34.15 % and an exergetic efficiency of 32.84 %. Additionally, the NG + 15 % HEF mixture reduces annual CO, CO2, and HC emissions by 9.52 %, 15.48 %, and 13.39 %, respectively. The addition of hydrogen positively impacts the engine's economic cost, allowing for a decrease of 1.56 % in the cost of useful work and a reduction of 3.32 % in the cost of exergy loss. In general, the proposed system for hydrogen production represents an alternative for utilizing the residual energy from exhaust gases, resulting in better performance parameters, reduced annual pollutant emissions, and lower economic costs.

9 April 2021 in Lubricants
Verified
Journal Article
Open access
PDF file
CGCarlos Eduardo Pardo García
Carlos Eduardo Pardo García
JSJhan Piero Rojas Suárez
Jhan Piero Rojas Suárez
SASofia Orjuela Abril
Sofia Orjuela Abril
In the present work, a numerical model is developed to investigate the influence of wear and misalignment on the bearings of a stationary diesel engine. The model implemented considers the effects of surface wear on the bearing, cavitation effects, and surface roughness. For the numerical analysis, changes in the surface roughness of σμσ=0.75 μm, σμσ=1 μm, and σμσ=1.25 μm are defined, and changes in the bearing load of 50%, 75%, and 100%. The results demonstrated that increasing the surface roughness intensifies the bearing wear, which represents 18% and 140% of the bearing clearance for the roughness of σμσ=1 μm and σμσ=1.25 μm, respectively. Additionally, the surface roughness causes a considerable increase in the bearing wear rate. The results described a maximum wear rate of μ20 μm/s. In general, increasing the bearing load by 25% doubles the hydrodynamic pressure conditions increases friction force by 33%, and reduces lubrication film thickness by 12%. The analysis of the angle of deflection, ϕx and ϕy, shows that the moment and the degree of misalignment tend to increase significantly with the increase in the magnitude of the angle ϕy. Negative angles of deflection, ϕx, produce a greater increase in the degree of misalignment and the moment. This implies a greater chance of contact with the bearing surface. In conclusion, the proposed methodology serves as a reliable tool to simultaneously evaluate key parameters on the tribological behavior of bearings that further extend their endurance and minimize wear damage.

18 February 2021 in Lubricants
Verified
Journal Article
Open access
PDF file
SASofia Orjuela Abril
Sofia Orjuela Abril
CGCarlos Eduardo Pardo García
Carlos Eduardo Pardo García
JLJhon Pabón León
Jhon Pabón León
Currently, internal combustion engines contribute to the problem of global warming due to their need to use products derived from fossil resources. To mitigate the above problem, this study proposes the use of coatings on the cylinder bore in order to reduce fuel consumption and polluting emissions. Therefore, in the present study a numerical model is developed in which the tribological behavior, heat fluxes, and leakage of the combustion gases in the chamber are considered to evaluate the influence of the coating. Nickel nanocomposite (NNC) and diamond-like carbon (DLC) coatings are considered in the study. The results demonstrate that the NNC coating produces a 32% reduction in the total friction force of the compression ring. The estimated maximum temperatures for the lubricating oil were 214, 202, and 194 °C for the DLC, steel, and NNC materials. Increasing the temperature in the DLC coating can cause a reduction in the tribological performance of the lubricant. The estimates made show that the implementation of the NNC coating allows a maximum reduction of 5.28 ton of fuel and 39.30 kg of CO emissions, which are based on the global fleet of diesel engines forecast for the year 2025 (corresponding to one hundred and eighty million engines) and a test time of 1800 s. The proposed numerical model allows future analyses to be carried out for other types of materials used as coatings. Additionally, the model can be expanded and adapted to consider other systems that involve friction processes in the engine.