An advantageous micromechanical technique to deposit large area graphene nanoplatelet (GNP) thin films on a low-density polyethylene substrate is proposed. This method is based on the application of shear-stress and friction forces to a graphite platelets/ethanol paste on the surface of a polymeric substrate; it allows us to obtain a continuous film of superimposed nanoplatelets mainly made of 13–30 graphene layers. X-ray diffraction (XRD), atomic force and transmission electron microscopy (TEM) measurements support the occurrence of a partial exfoliation of the graphite platelets due to shear-stress and friction forces applied during film formation. Scanning electron microscopy (SEM) observations point out that the surface of the polymer is uniformly coated by the overlap of GNPs, and TEM analysis reveals the tendency of the nanoplatelets to align parallel to the interface plane. It has been found that the deposited samples, under white light illumination, exhibit a negative photoconductivity and a linear photoresponse as a function of the applied voltage and the optical power density in the −120 ÷ 120 mV and 20.9 ÷ 286.2 mW cm −2 ranges, respectively.
Morphological, structural, and thermoresistive properties of films deposited on low-density polyethylene (LDPE) substrates are investigated for possible application in flexible electronics. Scanning and transmission electron microscopy analyses, and X-ray diffraction measurements show that the films consist of overlapped graphite nanoplatelets (GNP) each composed on average of 41 graphene layers. Differential scanning calorimetry and dynamic-mechanical-thermal analysis indicate that irreversible phase transitions and large variations of mechanical parameters in the polymer substrates can be avoided by limiting the temperature variations between −40 and 40 °C. Electrical measurements performed in such temperature range reveal that the resistance of GNP films on LDPE substrates increases as a function of the temperature, unlike the behavior of graphite-based materials in which the temperature coefficient of resistance is negative. The explanation is given by the strong influence of the thermal expansion properties of the LDPE substrates on the thermo-resistive features of GNP coating films. The results show that, narrowing the temperature range from 20 to 40 °C, the GNP on LDPE samples can work as temperature sensors having linear temperature-resistance relationship, while keeping constant the temperature and applying mechanical strains in the 0–4.2 × 10−3 range, they can operate as strain gauges with a gauge factor of about 48.
Large-area graphitic films, produced by an advantageous technique based on spraying a graphite lacquer on glass and low-density polyethylene (LDPE) substrates were studied for their thermoresistive applications. The spray technique uniformly covered the surface of the substrate by graphite platelet (GP) unities, which have a tendency to align parallel to the interfacial plane. Transmission electron microscopy analysis showed that the deposited films were composed of overlapped graphite platelets of different thickness, ranging from a few tens to hundreds of graphene layers, and Raman measurements provided evidence for a good graphitic quality of the material. The GP films deposited on glass and LDPE substrates exhibited different thermoresistive properties during cooling–heating cycles in the −40 to +40 °C range. Indeed, negative values of the temperature coefficient of resistance, ranging from −4 × 10−4 to −7 × 10−4 °C−1 have been observed on glass substrates, while positive values varying between 4 × 10−3 and 8 × 10−3 °C−1 were measured when the films were supported by LDPE. These behaviors were attributed to the different thermal expansion coefficients of the substrates. The appreciable thermoresistive properties of the graphite platelet films on LDPE could be useful for plastic electronic applications.
6 November 2017 in Journal of Vacuum Science & Technology B
Coatings of graphene nanoplatelets (GNPs) were deposited on a low density polyethylene (LDPE) substrate by a micromechanical method based on rubbing graphite platelets against the surface of the polymer. Transmission electron microscopy measurements reveal that the coatings were composed of nanoplatelets containing 13–30 graphene layers. Thermal gravimetric analysis shows that the investigated GNP coatings on LDPE (GNP/LDPE) samples are thermally stable up to 250 °C. Optical spectra of these samples, compared to those of pristine LDPE in the ultraviolet-visible-near-infrared range, indicate an increase in both reflectance and absorptance. On the other hand, the coating is able to markedly improve the surface conductivity of the polymeric substrate, indeed in the case of electrical contacts in the coplanar configuration (1 cm long and spaced 1 mm), the resistance of LDPE is 1015 Ω, while that of GNP/LDPE is 670 Ω. Electrical measurements under white light illumination point out a decrease in the conductance and a linear behavior of the photoconductance as a function of the optical power density. GNP/LDPE materials can be used for their optical, electrical, thermal, and flexibility properties in large area plastic electronics and optoelectronics.