We report on low-temperature and low-pressure deposition conditions of 140 °C and 1.5 mTorr, respectively, to achieve high-optical quality silicon nitride thin films. We deposit the silicon nitride films using an electron cyclotron resonance plasma-enhanced chemical vapour deposition (ECR-PECVD) chamber with Ar-diluted SiH4, and N2 gas. Variable-angle spectroscopic ellipsometry was used to determine the thickness and refractive index of the silicon nitride films, which ranged from 300 to 650 nm and 1.8 to 2.1 at 638 nm, respectively. We used Rutherford backscattering spectrometry to determine the chemical composition of the films, including oxygen contamination, and elastic recoil detection to characterize the removal of hydrogen after annealing. The as-deposited films are found to have variable relative silicon and nitrogen compositions with significant oxygen content and hydrogen incorporation of 10–20 and 17–21%, respectively. Atomic force microscopy measurements show a decrease in root mean square roughness after annealing for a variety of films. Prism coupling measurements show losses as low as 1.3, 0.3 and 1.5 ± 0.1 dB/cm at 638, 980 and 1550 nm, respectively, without the need for post-process annealing. Based on this study, we find that the as-deposited ECR-PECVD SiOxNy:Hz films have a suitable thickness, refractive index and optical loss for their use in visible and near-infrared integrated photonic devices.
We report on thermal and evanescent field sensing from a tellurium oxide optical microcavity resonator on a silicon photonics platform. The on-chip resonator structure is fabricated using silicon-photonics-compatible processing steps and consists of a silicon-on-insulator waveguide next to a circular trench that is coated in a tellurium oxide film. We characterize the device’s sensitivity by both changing the temperature and coating water over the chip and measuring the corresponding shift in the cavity resonance wavelength for different tellurium oxide film thicknesses. We obtain a thermal sensitivity of up to 47 pm/°C and a limit of detection of 2.2 × 10−3 RIU for a device with an evanescent field sensitivity of 10.6 nm/RIU. These results demonstrate a promising approach to integrating tellurium oxide and other novel microcavity materials into silicon microphotonic circuits for new sensing applications.
We present the design and experimental measurement of tellurium oxide-clad silicon microring resonators with internal Q factors of up to 1.5 × 106, corresponding to a propagation loss of 0.42 dB/cm at wavelengths around 1550 nm. This compares to a propagation loss of 3.4 dB/cm for unclad waveguides and 0.97 dB/cm for waveguides clad with SiO2. We compared our experimental results with the Payne–Lacey model describing propagation dominated by sidewall scattering. We conclude that the relative increase in the refractive index of TeO2 reduces scattering sufficiently to account for the low propagation loss. These results, in combination with the promising optical properties of TeO2, provide a further step towards realizing compact, monolithic, and low-loss passive, nonlinear, and rare-earth-doped active integrated photonic devices on a silicon photonic platform.
We report on UV laser photoresist mask writing as a tool for fabricating integrated optical waveguides and devices. Using 375 nm laser light and a pneumatically controlled direct writing stage, we defined mask features into a 250-nm-thick negative photoresist layer on a silicon nitride film on an oxidized silicon substrate. We investigated the feature size and edge roughness for different laser powers. Using the photoresist mask layer and reactive ion etching, we patterned high-refractive-index-contrast silicon nitride strip waveguides and devices with varying waveguide widths and gaps. We report on the structural and transmission characteristics of a directional coupler, Sagnac interferometer, and ring resonator and demonstrate 50/50 coupling at 1510 nm, 20 dB transmission drop at 1580 nm, and a Q factor of ∼13,000 at 1576 nm, respectively. These results demonstrate that this technique can be applied to a variety of thin film materials and substrates for inexpensive and rapid prototyping of integrated photonic devices.
We report on silicon waveguide distributed Bragg reflector (DBR) cavities hybridized with a tellurium dioxide (TeO2) cladding and coated in plasma functionalized poly (methyl methacrylate) (PMMA) for label free biological sensors. We describe the device structure and fabrication steps, including reactive sputtering of TeO2 and spin coating and plasma functionalization of PMMA on foundry processed Si chips, as well as the characterization of two DBR designs via thermal, water, and bovine serum albumin (BSA) protein sensing. Plasma treatment on the PMMA films was shown to decrease the water droplet contact angle from ∼70 to ∼35°, increasing hydrophilicity for liquid sensing, while adding functional groups on the surface of the sensors intended to assist with immobilization of BSA molecules. Thermal, water and protein sensing were demonstrated on two DBR designs, including waveguide-connected sidewall (SW) and waveguide-adjacent multi-piece (MP) gratings. Limits of detection of 60 and 300 × 10−4 RIU were measured via water sensing, and thermal sensitivities of 0.11 and 0.13 nm/°C were measured from 25–50 °C for SW and MP DBR cavities, respectively. Plasma treatment was shown to enable protein immobilization and sensing of BSA molecules at a concentration of 2 µg/mL diluted in phosphate buffered saline, demonstrating a ∼1.6 nm resonance shift and subsequent full recovery to baseline after stripping the proteins with sodium dodecyl sulfate for a MP DBR device. These results are a promising step towards active and laser-based sensors using rare-earth-doped TeO2 in silicon photonic circuits, which can be subsequently coated in PMMA and functionalized via plasma treatment for label free biological sensing.