Silicon photonics is an ideal platform for low‐cost, energy‐efficient, and high‐performance optical microsystems. However, because silicon is an inefficient light emitting material, the development of simple, inexpensive, and scalable monolithic amplifiers and light sources has been a significant challenge. Here, optical gain and lasing in an ultra‐compact hybrid rare‐earth silicon microdisk resonator are reported. The microdisk design is straightforward and compatible with the fabrication steps and device dimensions available in all silicon photonics foundries, while the thulium‐doped tellurite gain medium is added in a low‐temperature single‐step sputter deposition. This approach allows for low‐cost and high‐volume wafer‐scale manufacturing and co‐integration of rare‐earth amplifiers and light sources with silicon passive and active devices with no adjustment to standard process flows. The hybrid laser is pumped at standard telecom wavelengths around 1.6 µm and exhibits stable single‐mode emission at 1.9 µm, with an internal slope efficiency of 60% and >1 mW on‐chip output power. The laser is highly promising for emerging communications and sensing applications and opens new possibilities for the development of monolithic rare‐earth optical amplifiers and lasers directly on silicon.
We demonstrate compact, monolithically integrated thulium-doped tellurium oxide microring lasers on a low-loss silicon nitride platform. We observe lasing in the wavelength range of 1815–1895 nm under 1610 nm resonant pumping at varying waveguide-microring gap sizes and on-chip single-sided output powers up to 4.5 mW. The microlasers exhibit thresholds as low as 18 mW (11 mW) and a single-sided slope efficiency as high as 11% (17%) with respect to the pump power coupled into the TeO2:Tm3+-coated Si3N4 bus waveguide (absorbed pump power). These results are a promising development for integrated tellurite glass devices and light sources for the emerging 2-µm band in silicon nitride photonic integrated circuits.
We describe a rapid prototyping process for silicon nitride photonic integrated circuits operating at wavelengths around 1.3 and 1.5 μm. Moderate confinement silicon nitride waveguides and other essential integrated photonic components, such as fiber-chip couplers, microring resonators, multimode interference-based 3-dB power splitters, and subwavelength grating metamaterial waveguides, were fabricated and characterized and are reported. The prototyping platform features a 400-nm-thick layer of silicon nitride grown via low-pressure chemical vapour deposition onto 4” silicon thermal oxide wafers and uses direct-write electron beam lithography to define single mode waveguide structures that exhibit losses of < 1.3 dB/cm across the O-band (1260–1360 nm), < 1.8 dB/cm across the S-band (1460–1530 nm), < 1.6 dB/cm across the C-band (1530–1565 nm), and < 0.7 dB/cm across the L-band (1565–1625 nm) for both transverse electric (TE) and transverse magnetic (TM) polarizations. The reported components were compiled into a process design kit to accompany the platform, which is commercially available through the NanoSOI Design Center operated by Applied Nanotools Inc. with five multi-project wafer runs per year that have fast turnaround times on the scale of weeks rather than months. This provides a route toward the rapid fabrication of silicon nitride chip-based passive and thermo-optic active photonic devices with critical resolution down to 120 nm, making it an attractive solution for entry-level designers, device innovators, and small companies looking to incorporate integrated silicon nitride circuits into early-stage applications of silicon photonics.
We present the design and experimental measurement of tellurium oxide-clad silicon microring resonators with internal Q factors of up to 1.5 × 106, corresponding to a propagation loss of 0.42 dB/cm at wavelengths around 1550 nm. This compares to a propagation loss of 3.4 dB/cm for unclad waveguides and 0.97 dB/cm for waveguides clad with SiO2. We compared our experimental results with the Payne–Lacey model describing propagation dominated by sidewall scattering. We conclude that the relative increase in the refractive index of TeO2 reduces scattering sufficiently to account for the low propagation loss. These results, in combination with the promising optical properties of TeO2, provide a further step towards realizing compact, monolithic, and low-loss passive, nonlinear, and rare-earth-doped active integrated photonic devices on a silicon photonic platform.
We demonstrate low-threshold and wide emission wavelength range hybrid-integrated silicon-thulium microdisk lasers based on a pulley-coupled design. The resonators are fabricated on a silicon-on-insulator platform using a standard foundry process and the gain medium is deposited using a straightforward, low-temperature post-processing step. We show lasing in 40- and 60-µm diameter microdisks with up to 2.6 mW double-sided output power and bidirectional slope efficiencies of up to 13.4% with respect to 1620 nm pump power launched to the bus waveguides. We observe thresholds less than 1 mW versus on-chip pump power and both single-mode and multimode laser emission spanning across wavelengths from 1825 to 1939nm. These low threshold lasers with emissions over a > 100 nm range open the door to monolithic silicon photonic integrated circuits with broadband optical gain and highly compact and efficient light sources in the emerging ∼1.8–2.0 µm wavelength band.
We report on silicon waveguide distributed Bragg reflector (DBR) cavities hybridized with a tellurium dioxide (TeO2) cladding and coated in plasma functionalized poly (methyl methacrylate) (PMMA) for label free biological sensors. We describe the device structure and fabrication steps, including reactive sputtering of TeO2 and spin coating and plasma functionalization of PMMA on foundry processed Si chips, as well as the characterization of two DBR designs via thermal, water, and bovine serum albumin (BSA) protein sensing. Plasma treatment on the PMMA films was shown to decrease the water droplet contact angle from ∼70 to ∼35°, increasing hydrophilicity for liquid sensing, while adding functional groups on the surface of the sensors intended to assist with immobilization of BSA molecules. Thermal, water and protein sensing were demonstrated on two DBR designs, including waveguide-connected sidewall (SW) and waveguide-adjacent multi-piece (MP) gratings. Limits of detection of 60 and 300 × 10−4 RIU were measured via water sensing, and thermal sensitivities of 0.11 and 0.13 nm/°C were measured from 25–50 °C for SW and MP DBR cavities, respectively. Plasma treatment was shown to enable protein immobilization and sensing of BSA molecules at a concentration of 2 µg/mL diluted in phosphate buffered saline, demonstrating a ∼1.6 nm resonance shift and subsequent full recovery to baseline after stripping the proteins with sodium dodecyl sulfate for a MP DBR device. These results are a promising step towards active and laser-based sensors using rare-earth-doped TeO2 in silicon photonic circuits, which can be subsequently coated in PMMA and functionalized via plasma treatment for label free biological sensing.