Pekka Vallittu

Prof. Pekka Vallittu


Research Focus & Metrics

Academic Career Length

30Years (1997-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

1 October 2000 in The Journal of Prosthetic Dentistry
Verified
Journal Article
Closed access
PVPekka Vallittu
Pekka Vallittu
CSCamilla Sevelius
Camilla Sevelius

1 May 2018 in Dental Materials
Verified
Journal Article
Closed access
PVPekka Vallittu
Pekka Vallittu
ABAldo R. Boccaccini
Aldo R. Boccaccini
LHLeena Hupa
Leena Hupa
DWDavid C. Watts
David C. Watts

1 February 1998 in European Journal of Oral Sciences
Verified
Journal Article
Closed access
PDF file
PVPekka Vallittu
Pekka Vallittu
IRI. Eystein Ruyter
I. Eystein Ruyter
SBSebnem Buykuilmaz
Sebnem Buykuilmaz

Verified
Journal Article
Open access
PDF file
RRRavikumar Ramakrishnaiah
Ravikumar Ramakrishnaiah
AKAbdul Aziz Abdullah Al Kheraif
Abdul Aziz Abdullah Al Kheraif
DDDarshan Devang Divakar
Darshan Devang Divakar
JMJukka Matinlinna
Jukka Matinlinna
PVPekka Vallittu
Pekka Vallittu
The current laboratory study is evaluating the effect of hydrofluoric acid etching duration on the surface characteristics of five silica-based glass ceramics. Changes in the pore pattern, crystal structure, roughness, and wettability were compared and evaluated. Seventy-five rectangularly shaped specimens were cut from each material (IPS e-max™, Dentsply Celtra™, Vita Suprinity™, Vita mark II™, and Vita Suprinity FC™); the sectioned samples were finished, polished, and ultrasonically cleaned. Specimens were randomly assigned into study groups: control (no etching) and four experimental groups (20, 40, 80 and 160 s of etching). The etched surfaces’ microstructure including crystal structure, pore pattern, pore depth, and pore width was studied under a scanning electron microscope, and the surface roughness and wettability were analyzed using a non-contact surface profilometer and a contact angle measuring device, respectively. The results were statistically analyzed using one-way analysis of variance (ANOVA) and the post hoc Tukey’s test. The results showed a significant change in the pore number, pore pattern, crystal structure, surface roughness, and wettability with increased etching duration. Etching for a short time resulted in small pores, and etching for longer times resulted in wider, irregular grooves. A significant increase in the surface roughness and wettability was observed with an increase in the etching duration. The findings also suggested a strong association between the surface roughness and wettability.

3 October 2021 in Materials
Verified
Journal Article
Open access
PDF file
LPLeila Perea-Lowery
Leila Perea-Lowery
MGMona Gibreel
Mona Gibreel
PVPekka Vallittu
Pekka Vallittu
Lippo LassilaLippo Lassila
Lippo Lassila
The aim of this work was to investigate the effect of two post-curing methods on the mechanical properties of a 3D-printed denture base material. Additionally, to compare the mechanical properties of that 3D-printed material with those of conventional autopolymerizing and a heat-cured denture base material. A resin for 3D-printing denture base (Imprimo®), a heat-polymerizing acrylic resin (Paladon® 65), and an autopolymerizing acrylic resin (Palapress®) were investigated. Flexural strength, elastic modulus, fracture toughness, work of fracture, water sorption, and water solubility were evaluated. The 3D-printed test specimens were post-cured using two different units (Imprimo Cure® and Form Cure®). The tests were carried out after both dry and 30 days water storage. Data were collected and statistically analyzed. Resin type had a significant effect on the flexural strength, elastic modulus, fracture toughness, and work of fracture (p < 0.001). The flexural strength and elastic modulus for the heat-cured polymer were significantly the highest among all investigated groups regardless of the storage condition (p < 0.001). The fracture toughness and work of fracture of the 3D-printed material were significantly the lowest (p < 0.001). The heat-cured polymer had the lowest significant water solubility (p < 0.001). The post-curing method had an impact on the flexural strength of the investigated 3D-printed denture base material. The flexural strength, elastic modulus, fracture toughness, work of fracture of the 3D-printed material were inferior to those of the heat-cured one. Increased post-curing temperature may enhance the flexural properties of resin monomers used for 3D-printing dental appliances.