Mona Gibreel

Dr. Mona Gibreel

Turku University

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 October 2021 in Materials
Verified
Journal Article
Open access
PDF file
LPLeila Perea-Lowery
Leila Perea-Lowery
MGMona Gibreel
Mona Gibreel
PVPekka Vallittu
Pekka Vallittu
Lippo LassilaLippo Lassila
Lippo Lassila
The aim of this work was to investigate the effect of two post-curing methods on the mechanical properties of a 3D-printed denture base material. Additionally, to compare the mechanical properties of that 3D-printed material with those of conventional autopolymerizing and a heat-cured denture base material. A resin for 3D-printing denture base (Imprimo®), a heat-polymerizing acrylic resin (Paladon® 65), and an autopolymerizing acrylic resin (Palapress®) were investigated. Flexural strength, elastic modulus, fracture toughness, work of fracture, water sorption, and water solubility were evaluated. The 3D-printed test specimens were post-cured using two different units (Imprimo Cure® and Form Cure®). The tests were carried out after both dry and 30 days water storage. Data were collected and statistically analyzed. Resin type had a significant effect on the flexural strength, elastic modulus, fracture toughness, and work of fracture (p < 0.001). The flexural strength and elastic modulus for the heat-cured polymer were significantly the highest among all investigated groups regardless of the storage condition (p < 0.001). The fracture toughness and work of fracture of the 3D-printed material were significantly the lowest (p < 0.001). The heat-cured polymer had the lowest significant water solubility (p < 0.001). The post-curing method had an impact on the flexural strength of the investigated 3D-printed denture base material. The flexural strength, elastic modulus, fracture toughness, work of fracture of the 3D-printed material were inferior to those of the heat-cured one. Increased post-curing temperature may enhance the flexural properties of resin monomers used for 3D-printing dental appliances.

22 September 2022 in Polymers
Verified
Journal Article
Open access
PDF file
JWJunichiro Wada
Junichiro Wada
KWKanae Wada
Kanae Wada
MGMona Gibreel
Mona Gibreel
NWNoriyuki Wakabayashi
Noriyuki Wakabayashi
TITsutomu Iwamoto
Tsutomu Iwamoto
Lippo LassilaLippo Lassila
Lippo Lassila
Although three-dimensional (3D) printing is clinically convenient to fabricate occlusal splints, it is still unclear how the post-curing method and the printer type can affect 3D-printed splints. This study aimed to evaluate the effect of stroboscopic post-curing at a nitrogen gas (N2) atmosphere versus post-curing in an air atmosphere, as well as the printer type (liquid crystal display (LCD) and digital light processing (DLP)) on the mechanical properties of a 3D-printed hard-type occlusal splint material. Flexural strength, flexural modulus, Vickers hardness number (VHN), fracture toughness, degree of double bond conversion (DC), 3D microlayer structure, water sorption, and water solubility were evaluated. The post-curing method significantly affected all evaluated properties except fracture toughness and 3D microlayer structure, while the printer type significantly affected all evaluated properties except flexural strength and flexural modulus. VHN and DC were significantly higher, and the smoother surface was noticeably obtained when printed by LCD printer and post-cured at an N2 atmosphere. The current results suggested that the post-curing method and the printer type would play a role in the mechanical properties of the evaluated material and that the combination of post-curing at an N2 atmosphere and LCD printer could enhance its mechanical properties and surface smoothness.

1 December 2021 in Journal of the Mechanical Behavior of Biomedical Materials
Verified
Journal Article
Closed access
MGMona Gibreel
Mona Gibreel
LPLeila Perea-Lowery
Leila Perea-Lowery
PVPekka K. Vallittu
Pekka K. Vallittu
LLLippo Lassila
Lippo Lassila

31 October 2022 in Polymers
Verified
Journal Article
Open access
PDF file
JWJunichiro Wada
Junichiro Wada
KWKanae Wada
Kanae Wada
MGMona Gibreel
Mona Gibreel
NWNoriyuki Wakabayashi
Noriyuki Wakabayashi
TITsutomu Iwamoto
Tsutomu Iwamoto
Lippo LassilaLippo Lassila
Lippo Lassila
Despite the fact that three-dimensional (3D) printing is frequently used in the manufacturing of occlusal splints, the effects of the 3D printer type and post-curing methods are still unclear. The aim of this study was to investigate the effect of the printer type (digital light processing: DLP; and liquid crystal display: LCD) as well as the post-curing method with two different atmospheric conditions (air and nitrogen gas (N2)) on the mechanical and surface properties of 3D-printed soft-type occlusal splint material. The evaluated properties were flexural strength, flexural modulus, Vickers hardness (VHN), fracture toughness, degree of double bond conversion (DC%), water sorption, water solubility, and 3D microlayer structure. The printer type significantly affected all the evaluated properties. Flexural strength, flexural modulus, and fracture toughness were significantly higher when specimens were printed by a DLP printer, while VHN and DC% were significantly higher, and a smoother surface was noticeably obtained when printed by an LCD printer. The post-curing at an N2 atmosphere significantly enhanced all of the evaluated properties except water sorption, 3D microlayer structure, and fracture toughness. The current results suggested that the printer type and the post-curing methods would have an impact on the mechanical and surface properties of the evaluated material.

1 March 2019 in Journal of the Mechanical Behavior of Biomedical Materials
Verified
Journal Article
Closed access
MGMona Gibreel
Mona Gibreel
AKAhmed Khalifa
Ahmed Khalifa
MSMohamed Moustafa Said
Mohamed Moustafa Said
FMFatma Mahanna
Fatma Mahanna
NENesma El-Amier
Nesma El-Amier
PVPekka K. Vallittu
Pekka K. Vallittu

1 October 2018 in The Journal of Prosthetic Dentistry
Verified
Journal Article
Closed access
MGMona Gibreel
Mona Gibreel
LLLippo V.J. Lassila
Lippo V.J. Lassila
TNTimo O. Närhi
Timo O. Närhi
LPLeila Perea-Lowery
Leila Perea-Lowery
PVPekka K. Vallittu
Pekka K. Vallittu