Improving system lifetime and robustness is a key to advancing self-powered platforms for real world applications. A complete self-powered, battery-less, wearable platform requires a microwatt-power system-on-chip (SoC), operating reliably within this budget, capable of surviving long periods without charging, and recovering from power loss to its previous state. To meet these requirements, we designed a wireless sensing heterogeneous system-in-package (SiP) containing an ultra-low power (ULP) SoC, a non-volatile boot memory (NVM), and a 2.4 GHz frequency shift key (FSK) radio, all integrated with custom ULP interfaces. The SoC includes a fully integrated energy harvesting platform power manager (EH-PPM) to power the SiP and other commercial sensors. The EH-PPM is designed for small loads and powers the SoC and peripherals while drawing very low operating current. The SoC also includes a digital system data-flow for sensing applications, an analog front end for ECG signal acquisition, and a cold-boot management system (CBMS) for boot and recovery from the NVM. The CBMS enables integration of the SoC with the ULP NVM to create a wearable formfactor, self-powered system capable of recovery from power loss. The SoC also includes a radio interface tightly integrated with a compression accelerator to efficiently communicate with the FSK transmitter and reduce the FSK's transmission time. This tight integration between accelerators on the SoC and peripherals is another feature that reduces the system's power consumption by reducing the code size and number of memory accesses required to perform an operation. The SoC consumes 507 nW average power while running free-fall detection, 519 nW average power while measuring ambient temperature, and 1.02 μW during continuous ECG monitoring and post-processing.
This paper presents a top-down methodology for designing battery-less systems for the Internet-of-Things (IoT). We start by extracting features from a target IoT application and the environment in which it will be deployed. We then present strategies to translate these features into design choices that optimize the system and improve its reliability. We look into how to use these features to build the digital sub-system by determining the blocks to implement, the digital architecture, the clock rate of the system, the memory capacity, and the low power states. We also review how these features impact the choice of energy harvesting power management units.
We present an ultra-low power (ULP) 1 KB SRAM macro for Internet of Things (IoT) battery-less systems-on-chip (SoCs) operating under varying energy harvesting conditions. The unique combination of features within this array allows battery-less SoCs to retain important information for a significantly longer period of time when energy harvesting conditions are poor. The array uses 8T high-threshold (high-VT) static random access memory (SRAM) cells with word line boosting to eliminate write failures coupled with a read-before-write scheme to address read-disturb in half-selected cells. Due to the reduced on current in high-VT devices, read word line boosting is implemented to improve the drive strength of the read buffer, and to eliminate read failures. Leakage currents through the unselected cells during a read operation is addressed by boosting the footer virtual VSS (VVSS) of the read port to the supply voltage (VDD). To reduce the power consumption of instruction memories in battery-less SoCs, two features were utilized in this array: a read burst mode is used when reading consecutive addresses to reduce the read energy, and instructions with higher percentages of “1” data are defined since reading a “1” is less costly than reading a “0” in 8T cells. The proposed array can operate at a wide range of supply voltages (350–700 mV) and has two ULP modes: standby with retention (1.5 pW/bit) and shutdown without retention (0.13 pW/bit). Aggressive power gating of all peripherals during the standby state reduces the array power consumption down to 12.29 nW/KB at 320 mV with data retention. Compared to previously published 8T arrays, the proposed design provides the lowest standby power. The complete shutdown of the array allows further reduction down to 1.09 nW/KB and is suitable for reducing the power consumption of data memories in battery-less SoCs. The measured results from a commercial 130 nm chip show that the proposed array consumes a minimum of 6.24 pJ/access with a 17.16 nW standby power at 400 mV. The read burst mode allows up to 22% reduction in energy/access at 400 mV.