Internet of Things (IoT) devices such as wearable health monitors, augmented reality goggles, home automation, smart appliances, etc. are a trending topic of research. Various IoT products are thriving in the current electronics market. The IoT application needs such as portability, form factor, weight, etc. dictate the features of such devices. Small, portable, and lightweight IoT devices limit the usage of the primary energy source to a smaller rechargeable or non-rechargeable battery. As battery life and replacement time are critical issues in battery-operated or partially energy-harvested IoT devices, ultra-low-power (ULP) system on chips (SoC) are becoming a widespread solution of chip makers’ choice. Such ULP SoC requires both logic and the embedded static random access memory (SRAM) in the processor to operate at very low supply voltages. With technology scaling for bulk and FinFET devices, logic has demonstrated to operate at low minimum operating voltages (VMIN). However, due to process and temperature variation, SRAMs have higher VMIN in scaled processes that become a huge problem in designing ULP SoC cores. This chapter discusses the latest published circuits and architecture techniques to minimize the SRAM VMIN for scaled bulk and FinFET technologies and improve battery life for ULP IoT applications.
We present an ultra-low power (ULP) 1 KB SRAM macro for Internet of Things (IoT) battery-less systems-on-chip (SoCs) operating under varying energy harvesting conditions. The unique combination of features within this array allows battery-less SoCs to retain important information for a significantly longer period of time when energy harvesting conditions are poor. The array uses 8T high-threshold (high-VT) static random access memory (SRAM) cells with word line boosting to eliminate write failures coupled with a read-before-write scheme to address read-disturb in half-selected cells. Due to the reduced on current in high-VT devices, read word line boosting is implemented to improve the drive strength of the read buffer, and to eliminate read failures. Leakage currents through the unselected cells during a read operation is addressed by boosting the footer virtual VSS (VVSS) of the read port to the supply voltage (VDD). To reduce the power consumption of instruction memories in battery-less SoCs, two features were utilized in this array: a read burst mode is used when reading consecutive addresses to reduce the read energy, and instructions with higher percentages of “1” data are defined since reading a “1” is less costly than reading a “0” in 8T cells. The proposed array can operate at a wide range of supply voltages (350–700 mV) and has two ULP modes: standby with retention (1.5 pW/bit) and shutdown without retention (0.13 pW/bit). Aggressive power gating of all peripherals during the standby state reduces the array power consumption down to 12.29 nW/KB at 320 mV with data retention. Compared to previously published 8T arrays, the proposed design provides the lowest standby power. The complete shutdown of the array allows further reduction down to 1.09 nW/KB and is suitable for reducing the power consumption of data memories in battery-less SoCs. The measured results from a commercial 130 nm chip show that the proposed array consumes a minimum of 6.24 pJ/access with a 17.16 nW standby power at 400 mV. The read burst mode allows up to 22% reduction in energy/access at 400 mV.
Energy consumption is a key issue in portable biomedical devices that require uninterrupted biomedical data processing. As the battery life is critical for the user, these devices impose stringent energy constraints on SRAMs and other system on chip (SoC) components. Prior work shows that operating CMOS circuits at subthreshold supply voltages minimizes energy per operation. However, at subthreshold voltages, SRAM bitcells are sensitive to device variations, and conventional 6T SRAM bitcell is highly vulnerable to readability related errors in subthreshold operation due to lower read static noise margin (RSNM) and half-select issue problems. There are many robust subthreshold bitcells proposed in the literature that have some improvements in RSNM, write static noise margin (WSNM), leakage current, dynamic energy, and other metrics. In this paper, we compare our proposed bitcell with the state of the art subthreshold bitcells across various SRAM design knobs and show their trade-offs in a column mux scenario from the energy and delay metrics and the energy per operation metric standpoint. Our 9T half-select-free subthreshold bitcell has 2.05× lower mean read energy, 1.12× lower mean write energy, and 1.28× lower mean leakage current than conventional 8T bitcells at the TT_0.4V_27C corner. Our bitcell also supports the bitline interleaving technique that can cope with soft errors.
SRAMs occupy a large amount of area in modern system on chip circuits. With the growing trend of device scaling in deep sub-micron technologies, the 6T SRAM write operation is more vulnerable than the read operation from a failure standpoint. In order to make the SRAMs operate correctly, we must design them with some guard band above the minimum operating voltage (V MIN ) by designing for the worst case. In this paper, we investigate a reverse write assist circuit scheme that enables the tracking of SRAM write V MIN by using canary SRAM bitcells to track dynamic voltage, temperature fluctuations and aging effects. This circuit ultimately allows us to lower the write V MIN below the worst case corner (SF_85C) V MIN , which saves a minimum of 30.7% energy per cycle at the SS_85C, and a maximum of 51.5% energy per cycle at the FS_85C corner.
Operating both logic and memory at subthreshold supply voltages reduces energy dissipation for portable medical devices where battery life is critical. In this paper, we propose a 9T half-select-free subthreshold bitcell that has 2.05X lower mean read energy, 12.39% lower mean write energy, and 28% lower mean leakage current than conventional 8T bitcells at the TT_0.4V_27C corner. Our bitcell also supports the bitline interleaving technique that can cope with soft errors.