In this study, a three-dimensional (3D) response of anchored sheet pile walls was investigated on double-anchored sheet pile system during soils excavation and tunnel construction sequence. This construction procedure is executed in areas front and adjacent the sheet pile walls. This paper focused on both areas of construction effects on the sheet piles. This numerical study aimed at the evaluation of the variation of bottom wall bending moment, top wall lateral and vertical displacements and anchor reactions forces exerted in the sheet piles. This paper also described the variation of the total anchor's reactions forces from the upper and lower anchors rows. A parametric effect such as upper and lower anchors rows distance was also performed to evaluate the variation of the wall bending moment, displacement and anchors total forces. The analysis results indicated that the reactions forces developed in the lower anchor rods are always higher than those developed in the upper anchor rods. The higher the distance between the upper and the bottom anchors the lower the displacement of the top wall in any stage of the construction. The minimum bottom walls bending moment is developed in the case where the distance between the anchor's rows divided by the wall height is 0.51. Positioning the upper anchors at 0.15 and the lower at 0.39 the wall height from the top wall will induce minimum top wall vertical displacement during soil excavation. This paper presents the results and findings of the parametric study performed.
28 November 2019 in International Journal of Advanced Structural Engineering
In this study, a non-linear three-dimensional hydrocode numerical simulation was carried out using AUTODYN-3D, which is an extensive code dealing with explosion problems. A high explosive material (comp-B) is blasted against several concrete wall barriers. The model was first validated using referenced experimental tests and has shown good results. Several numerical models were carried out to study the effect of changing the shape of wall barrier from flat to convex curve and concave curve, and also investigated the effect of changing the angle of curvature. The results showed that changing the shape of a wall barrier from flat to convex curve has the best performance in mitigating the effect of blast waves. It is also concluded that convex walls with 60° angle of curvature have the best performance compared to other barrier walls.
Due to congestion in overground space, many underground structures have been built to facilitate communications between cities. These structures constructions will induce soil displacement, cities planning rearrangement, and sometimes are near to future buildings constructions. In some cases, communication channels should be built to allow the underground junction between the building and the subway station. Numerical simulation has been carried out to study the tunnel displacement behavior during construction stages. Two different procedures of the communication channel construction were also investigated. The results reliability were evaluated by monitoring six points displacement in the sheet pile walls after completion of the foundation pit. The results obtained were reasonably close to the monitoring results proven reasonably of the research ideas and the method scientificity. The results showed using sheet piles walls, and struts before soil excavation could reduce considerably the lateral displacement of the subway line during the excavation process and induce augmentation in the subway line vertical displacement. The lateral displacement effect of the walls thickness variation is much superior to the one provides by the struts cross-section and pile's diameter variations.
A pile foundation is commonly adopted for transferring superstructure loads into the ground in weaker soil. They diminish the settlement of the infrastructure and augment the soil-bearing capacity. This paper emphases the pile-driving effect on an existing adjacent cylindrical and semi-tapered pile. Driving a three-dimensional pile into the ground is fruitfully accomplished by combining the arbitrary Lagrangian–Eulerian (ALE) adaptive mesh and element deletion methods without adopting any assumptions that would simplify the simulation. Axial forces, bending moment, and lateral displacement were studied in the neighboring already-installed pile. An investigation was made into some factors affecting the forces and bending moment, such as pile spacing and the shape of the already-installed pile (cylindrical, tapered, or semi-tapered). An important response was observed in the impact of the driven pile on the nearby existing one, the bending moment and axial forces were not negligible, and when the pile was loaded, it was recommended to consider the coupling effect. Moreover, the adjacent semi-tapered pile was subjected to less axial and lateral movement than the cylindrical one with the same length and volume for taper angles smaller than 1.0°, and vice versa for taper angles greater than 1.4°.
In this study, the equivalent bending stiffness of cement-bonded joints connecting the porcelain bushing and flange in ultra-high voltage (UHV) electrical equipment was investigated. A mechanical bending model of the joint was developed based on its structural features, and a new equation for the equivalent bending stiffness of the joint was proposed. Based on experimental data for nine UHV porcelain bushings, a dimensionless elasticity coefficient for the equivalent bending stiffness equation was determined. Finally, considering two 1000 kV arresters as examples, the bending stiffness was calculated using the equation proposed in this paper and that which is used in China’s seismic code. A comparison of the results shows that the equation proposed in this study is in better agreement with the experimental data. Compared with the code equation, the equation in this paper adopts the expression for the dimensionless coefficient, which can more reasonably reveal the bending mechanism of the joint.
A method to identify the parameters of rolling resistance between particles in the discrete element method is proposed in this paper. Experiments revealed that a free rolling particle would swing back and forth marginally before it stops. We assume that the restoring force of the swing is mainly rolling resistance. An optical experimental system was designed to obtain the rolling resistance in the DEM model. A method to identify the parameters using the time history curve of the swing is proposed. We measured the time history of the angular displacement of cylindrical samples made of rubber and aluminum. In addition, the rolling stiffness and damping coefficients were identified. The identified parameters were applied to the discrete element model to simulate the experimental process. The results show that the time-history curve of swing obtained by DEM is in good agreement with the experimental curve. This verifies that the particle swings back and forth because of rolling resistance and that the parameters of the rolling resistance model can be determined by this experimental method