Due to their unique properties, alginate-based biomaterials have been extensively used to treat different diseases, and in the regeneration of diverse organs. A lot of research has been done by the different scientific community to develop biofilms for fulfilling the need for sustainable human health. The aim of this review is to hit upon a hydrogel enhancing the scope of utilization in biomedical applications. The presence of active sites in alginate hydrogels can be manipulated for managing various non-communicable diseases by encapsulating, with the bioactive component as a potential site for chemicals in developing drugs, or for delivering macromolecule nutrients. Gels are accepted for cell implantation in tissue regeneration, as they can transfer cells to the intended site. Thus, this review will accelerate advanced research avenues in tissue engineering and the potential of alginate biofilms in the healthcare sector.
4 September 2023 in Journal of Materials Research and Technology
Reinforced composite made of polypropylene combining banana and betel nut husk fiber (BBF) was treated with 10% NaOH (w/w). The fiber percentages of 40%, 50%, and 60% were used using the compression molding process. Properties such as tensile, bending, impact, thermogravimetric analysis (TGA), and water absorption were assessed as composite reinforcements. The composites with 50% BBF reinforcement performed better than composites with different fiber compositions. While 40% BBF-reinforced showed superior results in tensile, bending, and water absorption tests, the impact and TGA analyses provided comparatively lower results. The tensile strength (36 MPa), bending strength (78 MPa), energy absorption (2.4 Nm), thermal resistance (300–583°), and the maximum level of characteristics were attained. This work demonstrated the feasibility of repurposing waste banana stems and betel nut husks for interior decoration, furniture, and automobile bodies in fiber-reinforced hybrid composites, replacing expensive and environmentally hazardous artificial materials due to their mechanical capabilities.
The bottle gourd plant fibres (BGPF) and okra fibres were processed and refined (w/w 6 % NaOH) before being incorporated with polyolefin (polypropylene) for composite fabrication using a blending technique. The polyolefin matrix is used to develop composites with 5 % okra fibres and varying percentages (25, 30, 35 and 40 %) of BGPF. The results indicated that the "35 % BGPF +5 % okra +60 % polypropylene" composition achieved remarkable mechanical properties with tensile strength (26.95 MPa), tensile modulus (3.16 GPa), decreased elongation at break (1.71 %), bending strength (52.53 MPa), bending modulus (3.45 GPa), impact strength (14.25 kJ/m2), and hardness (69 D-shore). Moreover, these composites absorbed minimal water when a specific portion was submerged. The scanning electron microscopy (SEM) test on the composites revealed good fibre adhesion and adherence content between BGPF and okra fibres. Additionally, the thermo-gravimetric analysis and differential scanning calorimetry exhibited weight loss of composites during maximum cellulose degradation (80 %) at 483 °C. In the composites of the fibre-PP matrix, two distinct physical changes were observed indicating glass transition and degradation. However, the mechanical properties decreased after soil degradation. Thus, remarkable properties were achieved for the fibres-fibres and fibres-polyolefin (polypropylene) interfacial interactions.
7 March 2022 in Radiation Effects and Defects in Solids
Pineapple leaf fiber (PALF) reinforced epoxy resin-based composites were fabricated by using hand lay-up technique. The fiber content in the composites was taken as 25% (w/w), then it was modified by inserting 5% guar gum (polysaccharide) filler. Results demonstrated a 6% and 9% increase of tensile strength (TS) and tensile modulus (TM), respectively, over that of virgin PALF-epoxy composites. But 7% reduced elongation at break (Eb%) was noticed in this study. Results also revealed a 6% increase of bending properties due to insertion of guar gum filler. The virgin PALF-epoxy composites and along with guar gum filler PALF-epoxy composites were treated by gamma radiation doses varied from 2.5 to 10 kGy. The results revealed improved tensile and bending properties at 5 and 7.5 kGy, respectively. Sheared composite samples were immersed into deionized water and it was observed that both composites with and without filler absorbed a lower amount of water. The fiber-matrix adhesion was obtained by scanning electron microscopy (SEM) on both composites. The functional groups of the composites were also determined by Fourier transform infrared spectroscopy (FT-IR) and evaluated in this study.