This paper presents research on the synthesis and properties of the Mn_1.5Co_1.5O₄ (MC) spinel powder, as well as its application for the preparation of a MC thick film on the AL453 steel to be used for metallic interconnect material in IT-SOFCs. In order to prepare the MC micropowder with excellent homogeneity of the chemical and phase compositions, EDTA gel processes were utilized. In order to improve the contact electrical resistance between an AL453 steel interconnect and the La_0.8Sr_0.2FeO₃ (LSF) cathode and protect the cathode from Cr poisoning, the surface of the AL453 steel was coated with a protective manganese cobaltite spinel matrix using screen printing in combination with an appropriate heat treatment. The oxidation of the AL453/MC composite layer carried out in the air–H₂O gas mixture at 1,073 K for 55 h showed that the spinel coating may serve as an effective barrier against outward Cr diffusion from the AL453 steel and, therefore, significantly inhibit the formation of volatile Cr vapors from the chromia scale. The contact ASR study of the interconnect–cathode interface in the AL453/MC/LSCM/LSF/LSCM/MC/AL453 system carried out in the range of 723−1,073 K in air showed a very large drop in ASR compared to the resistance of the AL453/LSCM/LSF/LSCM/AL453 system without the spinel coating.

The study describes the physicochemical properties of transition metal (Co,Cu,Mg,Ni,Zn)O high-entropy oxide prepared using mechanochemical synthesis (MS) followed by thermal treatment, as well as the structural evolutions in the powder with milling time. The microstructure and electrical properties of the materials were studied using x-ray diffraction, scanning electron microscopy—energy dispersive spectroscopy and electrochemical impedance spectroscopy. The powders obtained after 30 h and 100 h of MS contained a mixture of two phases with a rock salt structure and, in addition, about 11 wt.% of Co₃O₄. Sintering these materials for 10 h in air at 1273 K led to the formation of a single-phase, solid solution with a rock salt structure. The developed sinters exhibited a fine-crystalline structure of grains and a uniform distribution of elements. The highest electrical conductivity was measured at 1148 K, and it was equal to 8.03 × 10⁻² S cm⁻¹.

The study presents the results of structural and electrical conductivity investigations of a Cu_1.3Mn_1.7O₄ spinel obtained using EDTA gel processes. An amorphous gel was synthesized and calcinated for 5 h in air at temperatures of 673, 773, 873, and 973 K. When calcinating the gel at temperatures below 973 K, the obtained powders consisted of two phases—the regular Cu_1.5Mn_1.5O₄ spinel and manganese(III) oxide. At 973 K, Mn₂O₃ was no longer observed, but a new Mn₃O₄ phase appeared in addition to the Cu_1.5Mn_1.5O₄ spinel. Green bodies prepared from these powders were sintered for 2 h in air at 1393 K. The obtained sinters had a porosity of around 12% and were composed predominantly of the spinel phase, with minor amounts of Mn₃O₄ and, in the case of three of four sinters—CuO. Electrical conductivity measurements were taken over the temperature range of 300-1073 K. A change in the character of conductivity of the studied sinters was observed in the range of 400-430 K, and it was associated with an increase in activation energy from 0.20 to 0.56 eV. The electrical conductivity of the studied sinters ranged from 74.8 to 88.4 S cm⁻¹, which makes the Cu_1.3Mn_1.7O₄ material suitable for application as a protective-conducting coating in IT-SOFC ferritic stainless steel interconnects.

Managing asbestos waste presents a significant challenge due to the widespread industrial use of this material, and the serious health and environmental risks it poses. Despite its unique properties, such as resistance to high temperatures and substantial mechanical strength, asbestos is a material with well-documented toxicity and carcinogenicity. Ensuring the safe removal and disposal of asbestos-containing materials (ACM) is crucial for protecting public health, the environment, and for reducing CO₂ emissions resulting from inefficient waste disposal methods. Traditional landfill disposal methods have proven inadequate, while modern approaches—including thermal, chemical, biotechnological, and mechanochemical methods—offer potential benefits but also come with limitations. In particular, thermal techniques that allow for asbestos degradation can significantly reduce environmental impact, while also providing the opportunity to repurpose disposal products into materials useful for cement production. Cement, a key component of concrete, can serve as a sustainable alternative, minimizing CO₂ emissions and reducing the need for primary raw materials. This work provides insights into research on asbestos waste management, offering a deeper understanding of key initiatives related to asbestos removal. It presents a comprehensive review of best practices, innovative technologies, and safe asbestos management strategies, with particular emphasis on their impact on sustainable development and CO₂ emission reduction. Additionally, it discusses public health hazards related to exposure to asbestos fibers, and worker protection during the asbestos disposal process. As highlighted in the review, one promising method is the currently available thermal degradation of asbestos. This method offers real opportunities for repurposing asbestos disposal products for cement production; thereby reducing CO₂ emissions, minimizing waste, and supporting sustainable construction.

The present study investigated the role of the reactive-element effect (REE) in improving the corrosion resistance, chromium vaporization rate, and electrical conductivity of the Fe–25Cr ferritic steel modified either by means of yttrium implantation or chemical deposition of yttrium oxide from metaloorganic compound vapors. The corrosion kinetics of the Fe–25Cr steel, both pure and modified, were determined under isothermal conditions in air and an Ar–H₂–H₂O gas mixture at 1,073 K. A significant improvement in corrosion resistance was observed after surface modification. XRD and SEM–EDS investigations showed that the protective Cr₂O₃ layer formed the main part of the scale. Measurements of Cr vaporization rate in the air–H₂O gas mixture revealed that both surface modifications of the steel significantly suppressed the formation of volatile chromium compounds to a large degree. The yttrium-implanted steels oxidized both in air and the Ar–H₂–H₂O mixture were characterized by the lowest area specific resistance and thereby did not exceed the acceptable ASR level (0.1 Ω cm²) for interconnect materials in the temperature range of 973–1,073 K, unlike pure steel and the steel coated with Y₂O₃.