In order to respond the growing interest towards radio frequency identification textile transponders, the authors propose a new approach to design radio frequency identification (RFID) devices by introducing the RFIDtex concept. The coupling system of inductive loops is implemented in the textronic structure with the RFID interface in order to split the transponder into two independently manufactured components. Then both modules can be easily integrated into the RFIDtex tag. The presented simulation and measurement results prove the concept of manufacturing a relatively small antenna in the form of a meandered dipole sewn in with a single thread, and further, that can be connected to the RFID chip through the coupling system without galvanic junctions. The achieved parameters clearly indicate that the tag can correctly communicate with the read/write device as well as the coupling between its both parts works properly, and the impedance matching is possible in this case. The possibility of confectioning products with electronic identification tags at the textile factory site and improved resistance to the impact of environmental conditions are the main advantage of the proposed approach to the RFID devices designing. The RFIDtex transponder idea proposed by the authors was restricted in the patent no PL 231291 B1.

The importance of the radio-frequency identification (RFID) technology and photovoltaic (PV) systems has been growing systematically in the modern world full of intelligent products connected to the Internet. Monitoring parameters of green energy plants is a crucial issue for efficient conversion of solar radiation, and cheap RFID transponders/sensors can be involved in this process to provide better performance of module supervision in scattered installations. Since many components of PV panels disturb the radio-wave propagation, research in the antenna scope has to be carried out to reach the proposed fusion. The problem with RFID transponders being detuned in close proximity to glass or metal surfaces can be solved on the basis of solutions known from the scientific literature. The authors went further, revealing a new antenna construction that can be fabricated straight on a cover glass of the PV panels. To achieve the established task, they incorporated advantages from the latest advancements in materials technology and low-power electronics and from the progress in understanding radio-wave propagation phenomena. The numerical model of the antenna was elaborated in the Hyper Lynx 3D EM software environment, and test samples were fabricated on the technology line of ML System Company. The convergence of calculated and measured antenna parameters confirms the design correctness. Thus, the studied antenna can be used to elaborate the cheap semipassive RFID transponders/sensors in the PV panel production lines.

Recent advances in the development of innovative textronic products are often related to the implementation of radio-frequency identification (RFID) technology. Such devices contain components of wireless telecommunications systems, in which radiofrequency circuits should be designed taking into account not only the frequency band or destined application, but also the dielectric properties of the materials. As is known from the theory of RFID systems, the dielectric permittivity and loss angle of the substrates significantly affect the performance of RFID transponders. Therefore, the knowledge on the variability of these parameters is highly important in the context of developing new solutions in textronic devices with the RFID interface. According to the plan of studies, at the beginning, the comprehensive characterization and determination of the dielectric parameters of various types of textile substrates were carried out. On this basis, the influence of fabrics on the performance of textronic RFID (RFIDtex) tags was characterized with numerical calculations. As the RFIDtex transponders proposed by the authors in the patent PL231291 have an outstanding design in which the antenna and the chip are located on physically separated substrates and are galvanically isolated, the special means had to be implemented when creating a numerical model. On the other hand, the great advantage of the developed construction was confirmed. Since the impedance at the chip’s terminals is primarily determined by the coupling system, the selected fabrics have relatively low impact on the efficiency of the RFIDtex transponder. Such an effect is impossible to achieve with classical designs of passive or semi-passive transponders. The correctness of the simulations was verified on the exemplary demonstrators, in threshold and rotation measurements performed at the laboratory stand.

The problem considered in the paper concerns the synthesis process of antennas for autonomous semi-passive RFID transponder/sensors dedicated to active glazing units. Glazing units are frequently used in modern multi-storey buildings to create amazing facades. When they are integrated with photovoltaic (PV) modules, active units are obtained. It is desirable, mainly for economic reasons and in order to ensure the high efficiency of a micro-photovoltaic power plant, that active glazing units are equipped with a system for monitoring their operating parameters. In connection with this, design problems occur that fall within the fields of sensor technology and radio communications. The main purpose of the presented study was to prepare appropriate input data for design tools used in the synthesis of antenna systems in the UHF band. Many important issues are considered including: proximity to structural elements of the building facade and PV cells, which disturbs the shape of the radiation pattern and affects the impedance parameters of the antenna system; the need to ensure easy integration of the RFID sensor and the specified object, without significant interference in the production of glazing units; appropriate shaping of the radiation pattern in order to enable reading and writing of the RFID tag from both inside and outside the building; impedance matching to the selected RFID chip in the broadest possible frequency range, etc.

The paper focuses on the synthesis of semi-passive RFID transponders-sensors that are intended to integrate with active glazing units with built-in photovoltaic cells. The main purpose of the designed construction of the UHF RFID device is to provide diagnostic information in the monitoring system of a photovoltaic micro-power plant. Furthermore, the RFID sensor is aimed at being implemented at various stages of the product life cycle: production, distribution, storage, installation, common operation, service/maintenance and disposal. In the presented research work, particular attention is paid to several aspects of the RFID sensor synthesis: use of the energy, generated periodically in the PV cells, to power the monitoring device that has to act permanently; specification of the PV module parameters that have to be monitored in the diagnostic process; implementation of data acquisition and energy management models in an electrical circuit; wireless data transfer to the master unit (monitoring host), even in the absence of power supply (e.g., module damage, blackout), using a standardized communication protocol IEC 18000-63 used in the RFID technology; and the design of the antenna system taking into consideration limitations of electronic technology and the material properties of substrates and glasses used in PV modules and RFID sensors. Based on the results of the investigations, the modular structure of the RFID sensor demonstrator is proposed. Moreover, several diagnostic scenarios are analyzed in detail. On the basis of the provided considerations, it is shown that in order to find a malfunctioning component, it is enough to compare the voltages on the photovoltaic modules that are in the close vicinity.