Thomas F. Landinger

Prof. Dr. Thomas F. Landinger

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2021 in Journal of Power Sources
Verified
Journal Article
Closed access
TLThomas F. Landinger
Thomas F. Landinger
GSGuenter Schwarzberger
Guenter Schwarzberger
AJAndreas Jossen
Andreas Jossen

9 June 2020 in IEEE Transactions on Electromagnetic Compatibility
Verified
Journal Article
Closed access
TLThomas F. Landinger
Thomas F. Landinger
GSGuenter Schwarzberger
Guenter Schwarzberger
Andreas JossenAndreas Jossen
Andreas Jossen
Lithium-ion (Li-ion) batteries in electric vehicles are exposed to high slew rate currents originating from the power electronics. Modern gallium nitride and silicon carbide-based power converters generate high switching frequencies, which propagate toward the battery. To predict the battery's impact on conducted emissions, we need to determine the battery's behavior over a high-frequency bandwidth. Traditional battery characterization techniques such as electrochemical impedance spectroscopy focus on frequencies below 10 kHz. This article proposes a novel method to characterize the battery beyond typical EIS frequencies. Developing a novel fixture to mount a single battery and applying proper de-embedding techniques enable a cell characterization from 1 kHz up to frequencies as high as 300 MHz using the 2-port shunt-through vector network analyzer (VNA) method. The cell's HF impedance originates from several loss processes such as skin effect, ionic shunt effect, and simple ohmic-inductive effects. First in literature, all these effects are measured and summarized in an equivalent electrical circuit model, which predicts the cell's impact on HF current pulses.

26 March 2021 in Energies
Verified
Journal Article
Open access
PDF file
TLThomas F. Landinger
Thomas F. Landinger
GSGuenter Schwarzberger
Guenter Schwarzberger
GHGuenter Hofer
Guenter Hofer
MRMatthias Rose
Matthias Rose
Andreas JossenAndreas Jossen
Andreas Jossen
As electric vehicles are gaining increasing worldwide interest, advances in driving range and safety become critical. Modern automotive battery management systems (BMS) compete with challenging performance and safety requirements and need to monitor a large amount of battery parameters. In this paper, we propose power line communications (PLC) for high voltage (HV) traction batteries to reduce the BMS wiring effort. By modeling a small-scale battery pack for frequencies up to 300 MHz, we predict the PLC channel transfer characteristics and validate the results using a PLC hardware demonstrator employing a narrowband single-carrier modulation. The results demonstrate that battery PLC is a demanding task due to low access impedances and cell coupling effects, yet transfer characteristics can be improved by optimal impedance matching. PLC for HV BMS not only saves weight and cost, but also improves flexibility in BMS design. PLC enables single-cell monitoring techniques such as online electrochemical impedance spectroscopy (EIS) without additional wiring. Online EIS can be used for in-situ state and temperature estimation saving extra sensors. This work unveils possible coexistence issues between PLC and battery monitoring. In particular, we demonstrate that certain PLC data or packet rates have to be avoided not to interfere with EIS measurements.

26 July 2021
Verified
Conference Paper
Closed access
HHHerbert Hackl
Herbert Hackl
MIMartin Ibel
Martin Ibel
TLThomas F. Landinger
Thomas F. Landinger
DPDavid J. Pommerenke
David J. Pommerenke
BABernhard Auinger
Bernhard Auinger
Knowledge of battery cell impedance is crucial for the design of many modern applications, as well as for predicting their electromagnetic compliance. For detailed 3D simulation of battery packs, single cells are commonly replaced with simplified bodies enhanced by internal impedance data obtained from measurement on real cells. Thereby it is necessary to exclude all influence of the measurement setup, i.e. to de-embed the cell impedance from exterior properties. In this work, two approaches are presented to extract the impedance of an 18650 Lithium-ion (Li-ion) cell from within a battery holder on a printed circuit board (PCB), using Open/Short/Load compensation (OSLC) and a copper cylinder as reference. By adding components in series and parallel to the cell, it is verified that the extraction result is not impacted by PCB circuitry, and also that the cell’s impedance is load-independent. Eventually, the test setup including Li-ion cell is replicated as electromagnetic (EM) simulation project. Two measurement-based methods to model the cell are compared, suitable for both 3D or circuit simulation. The frequency range under consideration is from 9 kHz to 1 GHz, whereas the presented approach proves reliable up to 200 MHz.