Herbert Hackl

Herbert Hackl

Auto-generated profile, based on publicly available information

Herbert Hackl

Division Power Electronics, Silicon Austria Labs GmbH, Graz, Austria

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 December 2022 in Electronics
Verified
Journal Article
Open access
PDF file
CRChristian Riener
Christian Riener
HHHerbert Hackl
Herbert Hackl
JHJan Hansen
Jan Hansen
ABAndreas Barchanski
Andreas Barchanski
TBThomas Bauernfeind
Thomas Bauernfeind
BABernhard Auinger
Bernhard Auinger
Energy efficiency is becoming one of the most important topics in electronics. Among others, wide band-gap semiconductors can raise efficiency and lead to shrinking volumes in power conversion systems. As different markets have regulations that require different designs, it is necessary to cope with a large variety of similar designs. By using effective modeling and simulation strategies, the efforts of building these variants can be diminished, and re-designs can be avoided. In this paper, we present a universally valid way to come to reasonable simulation results for conducted emissions of a power electronic system in the frequency range from 150 kHz up to 400 MHz. After giving an overview of the state-of-the-art, the authors show how to implement and set up a simulation environment for a gallium-nitride (GaN) power converter. It shows how to differentiate between important and not that important components for Electromagnetic Compatibility (EMC), how to model these components, the printed circuit board, the load, and the setup, including the Line Impedance Stabilization Networks (LISNs), etc. Multiport S-parameter strategies as well as vector fitting methods are employed. Computational costs are kept low, and all simulations are verified with measurements; thus, this model is valid up to 400 MHz.

1 November 2015
Verified
Conference Paper
Closed access
HHHerbert Hackl
Herbert Hackl
GWGunter Winkler
Gunter Winkler
BDBernd Deutschmann
Bernd Deutschmann
As the electromagnetic compatibility (EMC) of IC products takes on greater significance for competitiveness, IC manufacturers are increasingly interested in evaluating the EMC performance of their products as soon as during the very first design phase without the need of prototypes. There are a number of approaches to predict radiated emissions of automotive components as defined in the CISPR25 standard. However, it can be concluded that none of them are suitable for continuous use by the circuit designer itself because they either need a manufactured prototype and a lab engineer, or lots of simulation time and resources. The designer is normally no EMC expert and does not want to deal with additional, complex simulation tools. This paper presents the generation and use of a simulation model which can easily be implemented in the design environment (e.g. Cadence Virtuoso) used by the designer and does not notably increase the simulation time. The transient data is post-processed with a Matlab script emulating an EMI test receiver.

24 June 2022 in Electronics
Verified
Journal Article
Open access
PDF file
CRChristian Riener
Christian Riener
TBThomas Bauernfeind
Thomas Bauernfeind
SKSamuel Kvasnicka
Samuel Kvasnicka
KRKlaus Roppert
Klaus Roppert
HHHerbert Hackl
Herbert Hackl
MKManfred Kaltenbacher
Manfred Kaltenbacher
In this paper, common practice RF design guidelines for SMA edge mount connectors are investigated in terms of numerical simulations and VNA measurements. These guidelines are used in a variety of applications for coaxial-to-planar interfaces but often do not provide information regarding the physical origins of increased insertion and transmission losses. The presented results in this work focus on different RF PCB design features and their impact on electromagnetic field distributions in the launching zone. The presented investigations should raise awareness on the issue of electromagnetic field resonances occurring in the RF frequency range and assist PCB design engineers to identify potential issues occurring at an coaxial-to-planar interface. The investigated PCB features facilitate a high performance RF PCB design up to a frequency of 26 GHz.

1 June 2016
Verified
Conference Paper
Closed access
HHHerbert Hackl
Herbert Hackl
BABernhard Auinger
Bernhard Auinger
Radiated emissions generated by an integrated circuit (IC) during operation must not exceed specific limits. For automotive ICs this is verified by the standardized ALSE (Absorber Lined Shielded Enclosure) measurement setup defined in the CISPR 25 standard. This test especially targets the E-field emitted by a long cable harness attached to the device under test. Apart from simulations, analytical calculation models can be applied to quickly estimate the compliance test results. Typically the Hertzian dipole antenna model is used to calculate the electric field radiating from cables. But during the ALSE test radiated emissions from 150 kHz to 1GHz are measured in 1m distance. This results in very near field conditions for the lower frequencies, where the common prediction model is at its theoretical limits. As an alternative this paper demonstrates an electrostatic approach. For the frequency range of 100 kHz to 30MHz constant transmission factors are derived which yield the radiated emission spectrum when applied to the IC's output signal spectrum. The results of both calculation models are compared to measurement data.

17 August 2022 in IEEE Transactions on Signal and Power Integrity
Verified
Journal Article
Closed access
HHHerbert Hackl
Herbert Hackl
DPDavid J. Pommerenke
David J. Pommerenke
MIMartin Ibel
Martin Ibel
BABernhard Auinger
Bernhard Auinger
Batteries are a fundamental part of many modern electric systems. As a result, battery modeling is increasingly important for the prediction of signal and power integrity (SIPI) as well as electromagnetic compatibility (EMC). Conventional battery module modeling requires knowledge of the integrated cells first, which is usually obtained by measurement on single cells. However, if individual cells are not accessible, the single cell's impedance needs to be extracted from measurement of the complete module. This work describes two solutions to this problem, which are both based on 3D electromagnetic (EM) simulation of the battery module with surrogate cell models to obtain S-parameters, which describe coupling effects inherent to the modules' geometry. By either fitting of the simulated module impedance to the measured data on circuit schematic level, or by numerical multiport de-embedding, the single cell impedance is extracted. Considered frequencies range from 9 kHz to 1 GHz.

16 March 2020 in e+i Elektrotechnik und Informationstechnik
Verified
Journal Article
Open access
PDF file
HHHerbert Hackl
Herbert Hackl
MIMartin Ibel
Martin Ibel
BABernhard Auinger
Bernhard Auinger
DLDominik List
Dominik List
CSChristian Stockreiter
Christian Stockreiter
The modeling of batteries for simulation is nowadays of increasing importance because their behavior and performance has significant influence on the operation of many modern systems, such as electric vehicles (EV), mobile devices, energy storage and many more. But batteries also play an important role in daily electromagnetic compatibility (EMC) testing and measurement tasks, namely if they are used for powering devices under test (DUT) or measurement equipment. In this paper, we demonstrate the impact of a commercial 9V block battery on the result of a bulk current injection (BCI) test when used to supply optical voltage probes attached to the DUT. To illustrate the battery’s impact by simulation, a 3D model of selfsame is developed based on its actual internal structure and applying state-of-the-art approaches for battery modeling and commercial 3D EM simulation software. The model is validated by comparison of measurement and simulation of DUT voltages and input current during an actual BCI test.