The development of technologies for the accelerated formation or decomposition of gas hydrates is an urgent topic. This will make it possible to utilize a gas, including associated petroleum one, into a hydrate state for its further use or to produce natural gas from hydrate-saturated sediments. In this work, the effect of water content in wide range (0.7–50 mass%) and the size of quartz sand particles (porous medium; <50 μm, 125–160 μm and unsifted sand) on the formation of methane and methane-propane hydrates at close conditions (subcooling value) has been studied. High-pressure differential scanning calorimetry and X-ray computed tomography techniques were employed to analyze the hydrate formation process and pore sizes, respectively. The exponential growth of water to hydrate conversion with a decrease in the water content due to the rise of water–gas surface available for hydrate formation was revealed. Sieving the quartz sand resulted in a significant increase in water to hydrate conversion (59% for original sand compared to more than 90% for sieved sand). It was supposed that water suction due to the capillary forces influences both methane and methane-propane hydrates formation as well with latent hydrate forming up to 60% either without a detectable heat flow or during the ice melting. This emphasizes the importance of being developed for water–gas (ice–gas) interface to effectively transform water into the hydrate state. In any case, the ice melting (presence of thawing water) may allow a higher conversion degree. Varying the water content and the sand grain size allows to control the degree of water to hydrate conversion and subcooling achieved before the hydrate formation. Taking into account experimental error, the equilibrium conditions of hydrates formation do not change in all studied cases. The data obtained can be useful in developing a method for obtaining hydrates under static conditions.

Polymeric models of the core prepared with a Raise3D Pro2 3D printer were employed for methane hydrate formation. Polylactic acid (PLA), acrylonitrile butadiene styrene (ABS), carbon fiber reinforced polyamide-6 (UltraX), thermoplastic polyurethane (PolyFlex), and polycarbonate (ePC) were used for printing. Each plastic core was rescanned using X-ray tomography to identify the effective porosity volumes. It was revealed that the polymer type matters in enhancing methane hydrate formation. All polymer cores except PolyFlex promoted the hydrate growth (up to complete water-to-hydrate conversion with PLA core). At the same time, changing the filling degree of the porous volume with water from partial to complete decreased the efficiency of hydrate growth by two times. Nevertheless, the polymer type variation allowed three main features: (1) managing the hydrate growth direction via water or gas preferential transfer through the effective porosity; (2) the blowing of hydrate crystals into the volume of water; and (3) the growth of hydrate arrays from the steel walls of the cell towards the polymer core due to defects in the hydrate crust, providing an additional contact between water and gas. These features are probably controlled by the hydrophobicity of the pore surface. The proper filament selection allows the hydrate formation mode to be set for specific process requirements.

The selection of effective surfactants potentially can mobilize oil up to 50% of residuals in mature carbonate oilfields. Surfactants’ screening for such oilfields usually is complicated by the high salinity of water, high lipophilicity of the rock surface, and the heterogeneous structure. A consideration of features of the oilfield properties, as well as separate production zones, can increase the deep insight of surfactants’ influence and increase the effectiveness of surfactant flooding. This article is devoted to the screening of surfactants for two production zones (Bashkirian and Vereian) of the Ivinskoe carbonate oilfield with high water salinity and heterogeneity. The standard core study of both production zones revealed no significant differences in permeability and porosity. On the other hand, an X-ray study of core samples showed differences in their structure and the presence of microporosity in the Bashkirian stage. The effectiveness of four different types of surfactants and surfactant blends were evaluated for both production zones by two different oil displacement mechanisms: spontaneous imbibition and filtration experiments. Results showed the higher effect of surfactants on wettability alteration and imbibition mechanisms for the Bashkirian cores with microporosity and a higher oil displacement factor in the flooding experiments for the Vereian homogeneous cores with lower oil viscosity.