Joshua Stroh

Dr. Joshua Stroh


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 May 2020 in International Journal of Metalcasting
Verified
Journal Article
Closed access
PDF file
JSJoshua Stroh
Joshua Stroh
DSDimitry Sediako
Dimitry Sediako
DWDavid Weiss
David Weiss

15 May 2023 in Metals
Verified
Journal Article
Open access
PDF file
JKJordan Roger Kozakevich
Jordan Roger Kozakevich
JSJoshua Stroh
Joshua Stroh
DSDimitry Sediako
Dimitry Sediako
DWDavid Weiss
David Weiss
Heat-treated aluminum–silicon (Al-Si)-based alloys have dominated the cast lightweight alloy industry for several decades. However, in the last decade, Al-Ce-based alloys have shown promise in replacing Al-Si alloys as they remove the need for costly heat treatments. As the properties of Al-Ce alloys depend on the as-cast microstructure, it is important to characterize the solidification kinetics of these alloys. Therefore, this study focused on characterizing the solidification of an Al-Ce alloy with additions of Ni and Mn (nominal composition Al-12.37Ce-3.26Ni-0.94Mn-0.12Fe in weight percent). The alloy was cast in a wedge mold configuration, resulting in cooling rates between 0.18 and 14.27 °C/s. Scanning electron microscopy (SEM) coupled with the energy dispersive x-ray spectroscopy (EDS) and differential scanning calorimetry (DSC) techniques characterized the evolution rate of solid phases. The SEM/EDS data revealed that an Al10CeMn2 phase was present at higher cooling rates. At lower cooling rates, near the center of the casting, a primary Al23Ce4Ni6 phase was more present. It was observed that up to 2.6 atomic percent (at.%) of Mn was dissolved in this primary Al23Ce4Ni6 phase, thereby removing a large portion of the available Mn for forming the Al10CeMn2 phase. DSC analysis showed differences in the samples’ liquidus temperatures, which indicated compositional variations. Inductively coupled plasma–atomic emission spectroscopy (ICP-OES) and Scheil solidification simulations correlated the compositional differences with phase formation, which agreed with the SEM and DSC results. This experiment provides insight into novel Al-Ce-Ni-Mn alloys and where their potential lies in industrial applications.

13 May 2021 in Metals
Verified
Journal Article
Open access
PDF file
JSJoshua Stroh
Joshua Stroh
DSDimitry Sediako
Dimitry Sediako
DWDavid Weiss
David Weiss
Aimed at improving the tensile strength and creep resistance of a rare earth-modified A356 alloy, this study adjusted the Mg and Mn concentration in the alloy, specifically aiming to transform the harmful Al5FeSi and Al9FeSi3Mg5 phase into Al15(Fe,Mn)3Si2. It was found that lowering the Mg concentration from 0.49 to 0.25 wt.% and raising the Mn concentration from 0.10 to 0.41 wt.% resulted in a near complete transformation of the Fe-bearing phases. This transformation led to a greater total volume fraction of Fe-intermetallics (2.9 to 4.1%), without affecting the volume fraction of the desirable, temperature-resistant, AlSiRE phase. Moreover, the chemistry modification led to a shift in the morphology of the AlSiRE phase while reducing its size. Combined with the decreased volume fraction of the harmful Fe precipitates, the chemistry modification improved the yield strength (YS), ultimate tensile strength (UTS) and modulus of elasticity by ~14%, 9%, and 10%, respectively. In addition, the steady-state creep rates of the high Mn alloy were lower at all stresses as compared to the low Mn alloy and the fracture stress was ~15 MPa higher, reaching 100% of the alloy’s original 250 °C YS.

26 December 2018 in Materials Science Forum
Verified
Journal Article
Closed access
PDF file
DSDimitry Sediako
Dimitry Sediako
JSJoshua Stroh
Joshua Stroh
AMAlexandra McDougall
Alexandra McDougall
EAErmia Aghaie
Ermia Aghaie
Mercury Marine has used a new alloy, Mercalloy A362, for the manufacturing of a re-designed lower unit transmission gearcase. The enhanced strength of the alloy allowed for a substantial weight reduction in the new design. The purpose of this study was to examine and determine why cracking may develop in the gear casing during in service testing. Two types of material states, (i) as cast and (ii) heat treated were compared. Metallography and neutron diffraction analysis was carried out at locations identified as being areas of high stress by Magma software – which was performed in a separate study. Microstructural characterization at these locations revealed microstructural and the compositional differences. Differences in the porosity, eutectic phase, and volume fraction of the precipitates were observed at various locations of interest in each material state. The residual stress analysis was performed with application of neutron diffraction and revealed that the stresses in the as-cast component reached a maximum value of 120 MPa, which is below the yield strength of the alloy. The heat treatment applied to the castings reduced the stress by approximately 50 MPa. Based on the microstructure and neutron diffraction results, it is likely that performing a heat treatment process extends the lifetime of the component, however, it may not completely eliminate the cracking problem. Farther studies are currently nearing completion, targeting the mass production of the redesigned gearcase.

16 February 2019
Verified
Book Chapter
Open access
PDF file
JSJoshua Stroh
Joshua Stroh
APAustin Piche
Austin Piche
DSDimitry Sediako
Dimitry Sediako
ALAnthony Lombardi
Anthony Lombardi
GBGlenn Byczynski
Glenn Byczynski
A shift from ferrous to aluminum alloys for use in automotive engine blocks has significantly reduced the weight of vehicles and has consequently improved fuel economy while reducing harmful emissions. During the casting process of aluminum engine blocks, chilling devices are typically incorporated into the sand castings for faster cooling and to allow for a more uniform cooling rate. The effects that chills have on the alloys microstructure (i.e. size, morphology and SDAS) and mechanical properties have been studied in this paper. This study characterizes the microstructure throughout a modified 319 type aluminum inline-six engine block using scanning electron microscopy, energy dispersive spectroscopy and X-ray diffraction. In addition, mechanical testing (i.e. uniaxial tensile testing) have been performed at various depths along the cylinder web to determine the effects that varying microstructure has on the mechanical properties of the alloy. The results from this study indicate that the minor variation in cooling rates led to a fine and relatively uniform microstructure; resulting in the observation of similar mechanical properties throughout the entire cylinder bridge.

24 February 2021
Verified
Book Chapter
Closed access
PDF file
JSJoshua Stroh
Joshua Stroh
DSD. Sediako
D. Sediako
DWD. Weiss
D. Weiss