Jordan Roger Kozakevich

Mr. Jordan Roger Kozakevich

Faculty of Applied Science, The University of British Columbia, Kelowna, British Columbia, Canada
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 May 2023 in Metals
Verified
Journal Article
Open access
PDF file
JKJordan Roger Kozakevich
Jordan Roger Kozakevich
JSJoshua Stroh
Joshua Stroh
DSDimitry Sediako
Dimitry Sediako
DWDavid Weiss
David Weiss
Heat-treated aluminum–silicon (Al-Si)-based alloys have dominated the cast lightweight alloy industry for several decades. However, in the last decade, Al-Ce-based alloys have shown promise in replacing Al-Si alloys as they remove the need for costly heat treatments. As the properties of Al-Ce alloys depend on the as-cast microstructure, it is important to characterize the solidification kinetics of these alloys. Therefore, this study focused on characterizing the solidification of an Al-Ce alloy with additions of Ni and Mn (nominal composition Al-12.37Ce-3.26Ni-0.94Mn-0.12Fe in weight percent). The alloy was cast in a wedge mold configuration, resulting in cooling rates between 0.18 and 14.27 °C/s. Scanning electron microscopy (SEM) coupled with the energy dispersive x-ray spectroscopy (EDS) and differential scanning calorimetry (DSC) techniques characterized the evolution rate of solid phases. The SEM/EDS data revealed that an Al10CeMn2 phase was present at higher cooling rates. At lower cooling rates, near the center of the casting, a primary Al23Ce4Ni6 phase was more present. It was observed that up to 2.6 atomic percent (at.%) of Mn was dissolved in this primary Al23Ce4Ni6 phase, thereby removing a large portion of the available Mn for forming the Al10CeMn2 phase. DSC analysis showed differences in the samples’ liquidus temperatures, which indicated compositional variations. Inductively coupled plasma–atomic emission spectroscopy (ICP-OES) and Scheil solidification simulations correlated the compositional differences with phase formation, which agreed with the SEM and DSC results. This experiment provides insight into novel Al-Ce-Ni-Mn alloys and where their potential lies in industrial applications.

1 January 2022
Verified
Book Chapter
Closed access
PDF file
JKJordan Roger Kozakevich
Jordan Roger Kozakevich
JSJoshua Stroh
Joshua Stroh
VMVictor Mallouhi
Victor Mallouhi
DSDimitry Sediako
Dimitry Sediako
DWDavid Weiss
David Weiss

30 August 2024 in Materials
Verified
Journal Article
Open access
PDF file
JKJordan Roger Kozakevich
Jordan Roger Kozakevich
DSDimitry Sediako
Dimitry Sediako
DWDavid Weiss
David Weiss
Sven C. VogelSven C. Vogel
Sven C. Vogel
As the issue of climate change becomes more prevalent, engineers have focused on developing lightweight Al alloys capable of increasing the power density of powertrains. The characterization of these alloys has been focused on mechanical properties and less on the fundamental response of microstructures to achieve these properties. Therefore, this study assesses the quality of the microstructure of two high-temperature Al alloys (A356 + 3.5RE and Al-8Ce-10Mg), comparing them to T6 A356. These alloys underwent thermal conditioning at 250 and 300 °C for 200 h. Time-of-flight neutron diffraction experiments were performed before and after conditioning. The phase evolution was quantified using Rietveld refinement. It was found that the Si phase grows significantly (13–24%) in T6 A356, A356 + 3.5RE, and T6 A356 + 3.5RE alloys, which is typically correlated with a reduction in mechanical properties. Subjecting the A356 3.5RE alloy to a T6 heat treatment stabilizes the orthorhombic Al4Ce3Si6 and monoclinic β-Al5FeSi phases, making them resistant to thermal conditioning. These two phases are known for enhancing mechanical properties. Additionally, the T6 treatment reduced the vol.% of the cubic Al20CeTi2 and hexagonal ᴨ-Al9FeSi3Mg5 phases by 13% and 23%, respectively. These phases have detrimental mechanical properties. The Al-8Ce-10Mg alloy cubic β-Al3Mg2 phase showed significant growth (82–101%) in response to conditioning, while the orthorhombic Al11Ce3 phase remained stable. The growth of the beta phase is known to decrease the mechanical properties of this alloy. These efforts give valuable insight into how these alloys will perform and evolve in demanding high-temperature environments.

29 April 2022 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
JKJordan Roger Kozakevich
Jordan Roger Kozakevich
JSJoshua Stroh
Joshua Stroh
DSDimitry Sediako
Dimitry Sediako
DWDavid Weiss
David Weiss
ALAdam Loukus
Adam Loukus
SVSven C. Vogel
Sven C. Vogel

9 May 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
JKJordan Roger Kozakevich
Jordan Roger Kozakevich
JSJoshua Stroh
Joshua Stroh
DSDimitry Sediako
Dimitry Sediako
DWDavid Weiss
David Weiss
Heat-treated aluminum-silicon (Al-Si)-based alloys have dominated the cast lightweight alloy industry for several decades. However, in the last decade, Al-Ce-based alloys have shown promise in replacing Al-Si alloys due to their ability to remove the need for costly heat treatments. Since the properties of Al-Ce alloys depend on the as-cast microstructure, it is important to characterize the solidification kinetics of these alloys. Therefore, this study focused on characterizing the solidification of a near eutectic Al-Ce alloy with additions of Ni and Mn. The alloy was cast in a wedge mold configuration, resulting in cooling rates between 0.18 and 14.27 °C/s. SEM coupled with EDS and DSC techniques characterized the evolution rate of solid phases. The SEM/EDS data revealed that an Al10CeMn2 phase is present at higher cooling rates. At lower cooling rates, near the center of the casting, a proeutectic Al23Ce4Ni6 phase was more present. It was observed that up to 2.6 at. % of Mn was dissolved in this proeutectic Al23Ce4Ni6 phase, thereby removing a large portion of the available Mn for forming the Al10CeMn2 phase. DSC analysis showed differences in the samples' liquidus temperatures which is indicative of compositional variations. Inductively coupled plasma atomic emission spectroscopy (ICP-OES) and Scheil solidification simulations correlated the compositional differences to phase formation, which agreed with the SEM and DSC results. This experimentation provides insight into novel Al-Ce-Ni-Mn alloys and where their potential lies in industrial applications.

18 May 2026 in Materials Science and Engineering: A
Verified
Journal Article
Open access
JKJordan Roger Kozakevich
Jordan Roger Kozakevich
DSDimitry Sediako
Dimitry Sediako
DWDavid Weiss
David Weiss