Dimitry Sediako

Prof. Dr. Dimitry Sediako

Faculty of Applied Science, School of Engineering, The University of British Columbia, Okanagan Campus, Kelowna, BC V1V 1V7, Canada
orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 April 2011 in SAE International Journal of Materials and Manufacturing
Verified
Journal Article
Open access
PDF file
DSDimitry Sediako
Dimitry Sediako
FDFrancesco D'ELia
Francesco D'ELia
ALAnthony Lombardi
Anthony Lombardi
AMAlan Machin
Alan Machin
CRC. (Ravi) Ravindran
C. (Ravi) Ravindran
RMRobert Mackay
Robert Mackay
Continuous efforts to develop a lightweight alloy suitable for the most demanding applications in automotive industry resulted in a number of advanced aluminum (Al) and magnesium alloys and manufacturing routes. One example of this is the application of 319 Al alloy for production of 3.6L V6 gasoline engine blocks. Aluminum is sand cast around Fe-liner cylinder inserts, prior to undergoing the T7 heat treatment process. One of the critical factors determining the quality of the final product is the type, level, and profile of residual stresses along the Fe liners (or extent of liner distortion) that are always present in a cast component.In this study, neutron diffraction was used to characterize residual stresses along the Al and the Fe liners in the web region of the cast engine block. The strains were measured both in Al and Fe in hoop, radial, and axial orientations. The stresses were subsequently determined using generalized Hooke's law. Further, detailed microscopy and hardness measurements were performed from top to bottom along the interbore region of each cylinder. The microstructure was characterized using an optical and scanning electron microscope (SEM). Further, composition analyses were performed using energy dispersive X-ray spectroscopy (EDX). The results suggest that a variation in cooling rate along the cylinder caused a refinement of Al₂Cu, Al₁₅(Mn,Fe)₃Si₂ and eutectic silicon at the bottom of the cylinder. Increased cooling rate at the bottom of the cylinder also led to a more globular and uniform distribution of second phase particles, thereby resulting in increased hardness.This study gives invaluable insight on anticipated service properties of the engine block and demonstrates that neutron strain mapping is an efficient tool for optimization of manufacturing technologies.

1 February 2017 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
ALA. Lombardi
A. Lombardi
AEAbdallah Elsayed
Abdallah Elsayed
DSDimitry Sediako
Dimitry Sediako
CRC. Ravindran
C. Ravindran

15 May 2023 in Metals
Verified
Journal Article
Open access
PDF file
JKJordan Roger Kozakevich
Jordan Roger Kozakevich
JSJoshua Stroh
Joshua Stroh
DSDimitry Sediako
Dimitry Sediako
DWDavid Weiss
David Weiss
Heat-treated aluminum–silicon (Al-Si)-based alloys have dominated the cast lightweight alloy industry for several decades. However, in the last decade, Al-Ce-based alloys have shown promise in replacing Al-Si alloys as they remove the need for costly heat treatments. As the properties of Al-Ce alloys depend on the as-cast microstructure, it is important to characterize the solidification kinetics of these alloys. Therefore, this study focused on characterizing the solidification of an Al-Ce alloy with additions of Ni and Mn (nominal composition Al-12.37Ce-3.26Ni-0.94Mn-0.12Fe in weight percent). The alloy was cast in a wedge mold configuration, resulting in cooling rates between 0.18 and 14.27 °C/s. Scanning electron microscopy (SEM) coupled with the energy dispersive x-ray spectroscopy (EDS) and differential scanning calorimetry (DSC) techniques characterized the evolution rate of solid phases. The SEM/EDS data revealed that an Al10CeMn2 phase was present at higher cooling rates. At lower cooling rates, near the center of the casting, a primary Al23Ce4Ni6 phase was more present. It was observed that up to 2.6 atomic percent (at.%) of Mn was dissolved in this primary Al23Ce4Ni6 phase, thereby removing a large portion of the available Mn for forming the Al10CeMn2 phase. DSC analysis showed differences in the samples’ liquidus temperatures, which indicated compositional variations. Inductively coupled plasma–atomic emission spectroscopy (ICP-OES) and Scheil solidification simulations correlated the compositional differences with phase formation, which agreed with the SEM and DSC results. This experiment provides insight into novel Al-Ce-Ni-Mn alloys and where their potential lies in industrial applications.

2 July 2015 in Metallurgical and Materials Transactions A
Verified
Journal Article
Closed access
PDF file
DSDimitry Sediako
Dimitry Sediako
WKWojciech Kasprzak
Wojciech Kasprzak

19 February 2025 in Engineering Failure Analysis
Verified
Journal Article
Open access
RWRashiga Walallawita
Rashiga Walallawita
MHMatthew C. Hinchliff
Matthew C. Hinchliff
DSDimitry Sediako
Dimitry Sediako
JQJohn Quinn
John Quinn
VCVincent Chou
Vincent Chou
KWKim Walker
Kim Walker

4 October 2024 in Metals
Verified
Journal Article
Open access
PDF file
RWRashiga Walallawita
Rashiga Walallawita
MHMatthew C. Hinchliff
Matthew C. Hinchliff
DSDimitry Sediako
Dimitry Sediako
JQJOHN QUINN
JOHN QUINN
VCVincent Chou
Vincent Chou
MHMatthew Hill
Matthew Hill
This study employs a custom hollow specimen setup to investigate the HE in API 5L X60 pipeline base and welded materials exposed to pure hydrogen and a 20% hydrogen–natural gas blend at 2.07 MPa. Results indicate embrittlement with increasing hydrogen concentration. The base material showed a hydrogen embrittlement index (HEI) of 11.6% at 20% hydrogen and 12.4% at 100% hydrogen. For the welded material, the HEI was 14.6% at 20% hydrogen and 18.0% at 100% hydrogen. Fractography analysis revealed that the base and welded materials exhibited typical ductile fracture features in the absence of hydrogen, transitioning to a mixture of quasi-cleavage and micro-void coalescence (MVC) features in hydrogen environments. Additionally, with hydrogen, increased formation of secondary cracks was observed. Notably, the study identified the Hydrogen-Enhanced Localized Plasticity (HELP) mechanism as a probable contributor to hydrogen-assisted fracture.