Multiphase drives (MPDs) have been the subject of research for the last two decades. Despite being a technology that is still in the process of development, a significant number of research studies and developments have been reported in scientific literature over the past few years. This article aims to collect and present a review of these recent contributions, providing a comprehensive and insightful state of the art on this topic and future technology trends. The elaborated aspects include the advantages of multiphase machines, a general introduction to five-phase and six-phase machines, and their modelling techniques. In addition, new promising MPD topologies are covered. Recent advances in modulation techniques and the control of multilevel converters are also discussed. Finally, future trends and challenges in further developing this technology are discussed.

In this article, a switched reluctance machine (SRM) with six phases and a misaligned segmental rotor is proposed. The segmental rotor has an internal 15-degree misalignment, allowing the SRM structure to be a one-layer 2D structure with a short flux path structure. The proposed SRM produces a relatively low torque ripple by exciting two phases simultaneously. Additionally, an optimization method is applied, allowing for the maximum torque position of one phase to be aligned with the zero-torque position of the adjacent phase. The finite element method (FEM) is used to analyze and design the proposed SRM and to simulate the proposed liquid cooling system. The static torque waveforms are analyzed, and the dynamic torque waveforms are simulated with a drive using SiC MOSFETs. Finally, a prototype is manufactured, and the experiment is performed to validate the design and simulation results.

The brushless doubly fed reluctance machine (BDFRM) is receiving an increased amount of attention from the research community thanks to its potential as an alternative drive for variable speed applications, both as motor and generator. Currently, the sizing of the BDFRM in the literature is based on the model of an ideal axially laminated rotor (ALR) and discrepancies are hidden in compensation factors which are in turn tuned with a finite element analysis (FEA). This paper proposes an analytical framework to accurately model the air gap field modulation, and by extension the torque density, of the BDFRM with ducted segmental rotor (DSR) and salient pole rotor (SPR). The results are verified with FEA and validated on a BDFRM prototype.

This paper presents the comparisons between two types of switched reluctance machines (SRMs) and SRM converters. An SRM with a segmental rotor is compared with a conventional SRM (CSRM), and an SRM converter containing a passive boost circuit is compared with a conventional asymmetric half-bridge (AHB) converter. The segmental SRM has an asymmetric rotor with a segmented structure. The four rotor segments are made of steel laminations. Two segments are misaligned with the other two by 15 degrees. The torque ripple of the SRM with this structure is decreased, and the static torque is increased compared to a conventional SRM. The boost converter comprises a front-end circuit and a conventional AHB converter. The front-end circuit boosts the voltage level. The boosted voltage accelerates the rising and falling progress of the phase current. In this way, the SRM can obtain a greater speed and a smaller torque ripple. The comparison is conducted in simulation and validated through the experimental results. The experiment results have demonstrated that the segmental SRM obtains a maximum 7% torque ripple reduction at a low-speed range, compared to the CSRM. With the boost converter, both the CSRM and the segmental SRM can achieve a lower torque ripple and a higher maximum speed.

The Brushless Doubly Fed Reluctance Machine (BDFRM) is an emerging alternative for variable speed drive systems, providing a significant downsizing of the power electronics converter. This paper proposes a new view on the machine equations, allowing the reuse of the standard control system design for conventional synchronous and asynchronous machines: a cascade control system with an inner current control- and outer speed control loop. The assumptions and simplifications made on the machine model allow for a simple, model-based approach to set the controller gains in a brushless doubly fed machine drive system. The cascade control scheme is combined with an Unscented Kalman Filter as a state observer, capable of estimating the load torque and losses. The performance of the proposed control system design is checked in simulation and tested in real-time on a low power BDFRM prototype.

Torque fluctuations in drivetrains are the result of dynamic excitations and can be unfavorable for the lifetime of the system. Passive ripple suppression methods exist, such as torsional dampers and flywheels, which are often bulky and not always desired. Alternatively, performant active control methods exist; however, their applicability to certain drivetrains is not covered. Therefore, this paper focuses on active control from a mechanical perspective, more specifically, drivetrain dynamics impacting active control effectiveness. A quasi-resonant controller is implemented as an active control method, and its performance and robustness are proven both in simulation on a 3-DOF mechanical model and experimentally at different excitation frequencies. The tests show that active control effectiveness is highly drivetrain-dependent. In particular, the propagation of the torque oscillation is influenced by the elastic filtering properties of the drivetrain, and the speed ripple depends on the inertial attenuation of the drivetrain. High-stiffness, low-inertia drivetrains benefit best from active control for ripple suppression because the inertial attenuation is limited, while high-stiffness elements increase the mechanical bandwidth before dynamic decoupling happens between the inertias of interest. Active control serves as a viable alternative for speed ripple reduction when drivetrain compactness is key, instead of the current passive solutions.