Martin Miškiv-Pavlík

Dr. Martin Miškiv-Pavlík

Technical University of Košice, Faculty of Manufacturing Technologies, Department of Industrial Engineering and Informatics
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 December 2022 in Processes
Verified
Journal Article
Open access
PDF file
Jozef JurkoJozef Jurko
Jozef Jurko
Martin Miškiv-PavlíkMartin Miškiv-Pavlík
Martin Miškiv-Pavlík
Jozef HusárJozef Husár
Jozef Husár
PMPeter Michalik
Peter Michalik
Laser scanning technology has been used for several years. Nevertheless, no comprehensive study has been conducted to prove that the application of confocal chromatic sensor (CCHS) laser technology is effective and suitable to verify the integrity parameters of machined surfaces in terms of cutting tool damage. In this paper, the optimization and effects of five factors (cutting speed, feed, depth of cut, attachment length of the workpiece, and tip radius) on the roundness deviation measured by CCHS and, at the same time, on the amount of wear on the back side of the cutting part of the tool were studied according to ISO 3685, which was measured with a microscope. The results obtained were evaluated using the gray relational analysis method (GRA), in conjunction with the Taguchi method, and the significance of the factors was demonstrated using the analysis of variance (ANOVA) method.

23 May 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Jozef JurkoJozef Jurko
Jozef Jurko
Martin Miškiv-PavlíkMartin Miškiv-Pavlík
Martin Miškiv-Pavlík
VHVratislav Hladký
Vratislav Hladký
PLPeter Lazorík
Peter Lazorík
PMPeter Michalik
Peter Michalik
IPIgor Petruška
Igor Petruška
One of the most important operations in the technological production process is the inspection of the manufactured product. The gradual wear of the tool affects the achievement of the required quality of the functional surfaces. In this research, we present the results of measuring the diameter deviation with a new generation laser triangulation sensor (LTS). At the same time, we have performed parametric optimization of several multi-responses, such as insert wear on the VBB flank side of cutting edge and diameter deviation Δd for a C45 steel sample during dry turning and using a sintered carbide insert, using the method of grey relational analysis (GRA) in combination with the Taguchi L16 orthogonal array. The optimal setting of input factors for multi-response parameters is ap 4-f 4-vc 1 i.e., depth of cut 0.5 mm, feed 0.4 mm per revolution, and a cutting speed of 70 m/min. At the same time, we present an evaluation of the significance of input factors using the method ANOVA.

24 August 2021 in Processes
Verified
Journal Article
Open access
PDF file
Martin Miškiv-PavlíkMartin Miškiv-Pavlík
Martin Miškiv-Pavlík
Jozef JurkoJozef Jurko
Jozef Jurko
This paper describes the important significance of cutting-edge technology in the machining of polycrystalline diamond (PCD) cutting inserts by comparing the evaluation criteria. The LASER technology of cutting-edge machining is compared with grinding and electrical discharge machining (EDM) technologies. To evaluate the data from the experiments, the Grey Relational Analysis (GRA) method was used to optimize the input factors of turning to achieve the required output parameters, namely the deviation of roundness and chip cross-section. The input factors of cutting speed, feed rate, depth of cut and corner radius were applied in the experiment for three different levels (minimum, medium and maximum). The optimal input factors for turning of aluminum alloy (AW 5083) were determined for the factorial plan according to Grey Relational Grade based on the GRA method for the multi-criteria of the output parameters. The results were confirmed by a verification test according to the GRA method and optimal values of input factors were recommended for the machining of Al-alloy (AW 5083) products. This material is currently being developed by engineers for forming selected components for the automotive and railway industries, mainly to reduce weight and energy costs. The best values of the output parameters were obtained at a cutting speed of 870 m/min, feed rate of 0.1 mm/min, depth of cut of 0.5 mm and a corner radius of 1.2 mm.



7 October 2020 in MM Science Journal
Verified
Journal Article
Closed access
Kamil ZidekKamil Zidek
Kamil Zidek
Ján PiteľJán Piteľ
Ján Piteľ
Alexander HošovskýAlexander Hošovský
Alexander Hošovský
NLNatalia Lishchenko
Natalia Lishchenko
Martin Miškiv-PavlíkMartin Miškiv-Pavlík
Martin Miškiv-Pavlík
JZJozef Zbihej
Jozef Zbihej
The paper deals with the design of an automated measuring and error detection system integrated into the turning machine. The experimental measuring device is based on a laser sensor with data transfer to the PLC control system. The main advantage of the designed experimental system is the possib...