The blades of modern gas turbine engines are complex structures made of heat-resistant nickel alloys with a complex system of internal cavities. The article describes a method of strengthening samples of a heat-resistant Ni-Cr alloy by applying a composite coating (Cr-Al-Co + ZrO₂-Y₂O₃). The alloy prototypes were fabricated by vacuum melting. An ion-plasma technology of a two-layer coating with an inner metal and an outer ceramic layer on the prepared surface of the heat-resistant alloy matrix was developed. The morphology and structure of the alloy prototypes and the investigated composite coating were studied by scanning electron spectroscopy. The total thickness of the two-layer wear-resistant coating was 17–18 μm. The thickness of the inner layer (Cr/Al/Co) is 10–11 μm and the thickness of the outer ceramic coating (ZrO₂-Y₂O₃) is 6–7 μm. To improve the operational characteristics of the material, an electron-beam surface treatment was proposed. The research results showed a sevenfold increase in surface resistance compared with the initial state.

This article describes spark plasma sintering of ceramics based on silicon carbide with nanoadditives, as follows: MnO_nano 5.5 wt. % + Al₂O_3nano 2.0 wt. % + SiC_nm (37–57 wt. %) + SiC_µm (31–51 wt. %) + SiO_2µm 4.5 wt. %. Sintering was carried out at 2000 °C. The diffraction pattern of the analyzed sample showed the presence of silicon carbide with a hexagonal crystal lattice. Residual amounts of rhombohedral SiC, α-Fe, and a solid solution of silicon in iron were also found. The method of thermogravimetric analysis established the change in mass, heat flow, temperature of the samples, and the change in the partial pressures of gases during the experiment. Samples obtained by SPS show a higher density of the material at the level of 3.3 g/cm³, average mechanical strength of 454 MPa, and microhardness of 35 GPa, compared with samples obtained by liquid-phase sintering. The SPS method also made it possible to obtain materials with a higher density (by 8%) and practically no significant crystal growth compared to samples obtained by liquid phase sintering. The results of the study facilitate the achievement of a combination of new approaches to the design of compositions and the technology of manufacturing SiC ceramics, which significantly expands their areas of application.

The development of novel designs for hydropower plants is of high interest nowadays. Studies have shown the negative effect of fluid flow on the turbines of mini-hydropower plants when using them in the conditions of the mountain river. To reduce the damage caused by cavitation, a microplasma coating technique has been chosen. Due to its wetting ability, low density, high thermal conductivity, high heat resistance and low chemical activity, graphite has been studied as a coating material. Vanadium pentoxide has been added as an interlayer to increase the wear resistance, corrosion resistance, and adhesion of the system. The microstructure of the system was studied using scanning electron microscopy and transmission electron microscopy. Functional properties of the system were tested by microhardness tests, wear resistance tests (friction), corrosion tests, and pull-off tests. The surface of the coating was homogeneous without warping, swelling and cracking. The microstructure consisted of regular structures in the form of branches of dendrites. V₂O₅/C coating resulted in the increase in microhardness up to 2534 MPa. The wear resistance (volume loss) of the sample with double-layer coating was 0.14 mm³ and the maximum adhesion strength was 17.5 MPa. Thus, the double-layer microplasma V₂O₅/C coating was applied and studied for strengthening the blades of mini-HPP. The microplasma method can find application in modifying the surface of power equipment subjected to the cavitation effect of the river water.

This article presents a study of changes in the microstructure of Hadfield steel depending on the tensile deformation and cold rolling with the strain/stress level. It has been established that the change in the “σ-ε” curve (at ε = 5%) is accompanied by a 1.5-times decrease in the strain-hardening coefficient. At ε = 0 to 5%, the structure contains dislocation loops, the interweaving of elongated dislocations, single-layer stacking faults. At ε = 5%, the structure contains multilayer stacking faults and mechanical microtwins. At ε > 5%, there is an intense microtwinning with no long dislocations and stacking faults. The most intense twinning develops in the range of deformation degrees of 5–20%, while the number of twins in the pack increases from 3–4 at ε = 10% to 6–8 at ε = 20%. When mechanical twinning is included, a cellular dislocation substructure begins to develop intensively. The cell size decreases from 700 nm at ε = 5% to 150 nm at ε = 40%. Twinning develops predominantly in systems with the largest Schmid factor and facilitates the dislocation glide. The results may be of interest to the researchers of the deformation processes of austenitic alloys.

This article is devoted to the study of microwave-absorbing properties of Co-C coating applied by magnetron sputtering. This article presents the main results of the manufacturing of a Co-C coating by magnetron sputtering, and the evaluation of experimental and computational research data on the relationship between the structure and properties of the obtained films. The structure of Co-C systems has been modeled to control the resulting structures using X-ray diffraction analysis. The structural-phase state of the resulting thin-film Co-C systems and the microwave-absorbing properties of coatings were studied using the transmission line method, consisting of a vector network analyzer, an air coaxial line, a software program, and an external computer. It has been established that on the resulting Co-C film the reflection coefficient in the frequency range of 8.2–12.4 GHz varies in the range of 900 → 718 mU, with reflection losses of −0.86 → −2.57 dB, and a standing wave coefficient of 19 → 6.8. An analysis of the obtained data indicates the presence of losses of electromagnetic energy in the studied frequency range.

The article describes the effect of heat treatment on the structural-phase state and properties of a multilayer Cr-Al-Co-Y coating obtained by magnetron sputtering. Heat treatment was carried out at 400, 800 and 1000 °C. The study of the microstructure was carried out by electron microscopy with energy dispersive analysis and powder X-ray diffraction. The surface of the samples was studied by atomic force microscopy. The thickness of the Co-Cr-Al-Y coatings was 1.5–1.7 ± 0.2 µm. The obtained coatings are characterized by a hardness of 4.7–6.4 GPa. A distinctive feature of the layers is the absence of a crystalline structure in some areas of the coating. The main process occurring during the thermal treatment is the formation of a spinel-type phase. For a single-layer sample after heat treatment at 400 °C, it was not possible to fix extraneous reflections except for the reflections of the silicon substrate 111 and 220. For the rest of the samples, the appearance of reflections of a number of phases was noticed, such as: SiO₂, CoO, AlSi_0.5O_2.5 and CrAl_0.42Si_1.58. An increase in the treatment temperature up to 800 °C did not lead to significant changes. In the case of the multilayer sample, the reflections of various impurity phases disappeared and the Co₃O₄ phase was formed. For samples treated at 1000 °C, the formation of a spinel-type phase (Co₃O₄-CoCr₂O₄) was observed in all cases. Data on the structural-phase state and properties of the multilayer Co-Cr-Al-Y coating can be used to predict the nature of such coatings after heat treatment.