UHMWPE is resistant to acids, alkalis and radiation. Its combination of unique properties makes this material attractive for obtaining multifunctional coatings. However, in practice, obtaining coatings based on UHMWPE is associated with difficulties associated with low thermal conductivity and high viscosity of the material. The possibility of overcoming the technological problems of obtaining gas-thermal coatings based on UHMWPE was studied in the present work. A physical model of a flame with UHMWPE particles moving along the central axis was developed by the finite element method. The temperature along the central axis of the plume was determined. The interaction between a gas-thermal torch and a UHMWPE particle was established. It was determined that the residence time of UHMWPE particles in a gas-thermal flame is not enough for its complete penetration, which is the reason for the appearance of various defects. The interrelation of the particle heating rate in the torch depending on its diameter was determined. A new variant of coating deposition with preliminary heating of the powder in a fluidized bed was proposed. The thermal characteristics of UHMWPE powder were determined by differential scanning calorimetry and thermogravimetric analysis. The allowable temperature interval for UHMWPE deposition was established. Coatings were obtained under various deposition modes. It was established using the methods of X-ray diffraction analysis and infrared spectroscopy that the structure of the crystal lattice of UHMWPE did not change after deposition. Significant oxidation processes do not occur during spraying. It was found using scanning electron microscopy that the coatings obtained with preliminary heating of the powder in a fluidized bed do not have air inclusions. The obtained results make it possible to obtain higher quality coatings.
This article presents the results of a study of a composite coating made of ultrahigh molecular weight polyethylene (UHMWPE) with a diabase filler obtained by flame spraying. Diabase of 10 wt.%, 20 wt.%, 30 wt.% and 40 wt.% was chosen as a filler. The polymer coating was applied to the St3 metal substrate using temperature control in a conventional flame spraying process. The coating was studied using scanning electron microscopy, X-ray phase analysis, infrared spectroscopy, abrasive wear resistance, microhardness testing and determination of the friction coefficient. It has been shown that diabases do not have a negative effect on the initial chemical structure of UHMWPE and it is not subjected to destruction during flame spraying. The introduction of diabase into the composition of UHMWPE with a content of 10–40% of the total mass does not adversely affect the crystalline structure of the coating. It has been established that with an increase in the volume of the diabase filler, the wear resistance of the composite coating based on UHMWPE increases. It has been determined that with the addition of diabase, the microhardness of the coatings increases.
This article is devoted to the study of microwave-absorbing properties of Co-C coating applied by magnetron sputtering. This article presents the main results of the manufacturing of a Co-C coating by magnetron sputtering, and the evaluation of experimental and computational research data on the relationship between the structure and properties of the obtained films. The structure of Co-C systems has been modeled to control the resulting structures using X-ray diffraction analysis. The structural-phase state of the resulting thin-film Co-C systems and the microwave-absorbing properties of coatings were studied using the transmission line method, consisting of a vector network analyzer, an air coaxial line, a software program, and an external computer. It has been established that on the resulting Co-C film the reflection coefficient in the frequency range of 8.2–12.4 GHz varies in the range of 900 → 718 mU, with reflection losses of −0.86 → −2.57 dB, and a standing wave coefficient of 19 → 6.8. An analysis of the obtained data indicates the presence of losses of electromagnetic energy in the studied frequency range.
Multilayer thin films composed of cobalt (Co), carbon (C), and chromium (Cr) possess promising electromagnetic properties, yet the combined Co–C–Cr system remains underexplored, particularly regarding its performance as a microwave absorber. Existing research has primarily focused on binary Co–C or Co–Cr compositions, leaving a critical knowledge gap in understanding how ternary multilayer architectures influence electromagnetic behavior. This study addresses this gap by investigating the structure, phase composition, and microwave absorption performance of Co–C–Cr multilayer coatings fabricated via magnetron sputtering onto porous silicon substrates. This study compares four-layer and eight-layer configurations to assess how multilayer architecture affects impedance matching, reflection coefficients, and absorption characteristics within the 8.2–12.4 GHz frequency range. Structural analyses using X-ray diffraction and transmission electron microscopy confirm the coexistence of amorphous and nanocrystalline phases, which enhance absorption through dielectric and magnetic loss mechanisms. Both experimental and simulated results show that increasing the number of layers improves impedance gradients and broadens the operational bandwidth. The eight-layer coatings demonstrate a more uniform absorption response, while four-layer structures exhibit sharper resonant minima. These findings advance the understanding of ternary multilayer systems and contribute to the development of frequency-selective surfaces and broadband microwave shielding materials.
30 September 2025 in Bulletin of Shakarim University. Technical Sciences
Soil moisture plays a key role in the formation of surface runoff and floods, especially in conditions of spring snowmelt and extreme precipitation. The relevance of soil moisture monitoring is increasing for areas with high flood risk, such as the East Kazakhstan region. This article provides an overview of modern remote sensing (remote sensing) methods used to assess soil moisture in order to predict floods. Global and regional studies demonstrating the effectiveness of integrating satellite data (SMAP, Sentinel-1/2, SMOS, etc.) into hydrological models are considered. A comparative analysis of ground-based and remote methods of measuring soil moisture is carried out, approaches using radiometers, radars, multispectral sensors, as well as unmanned aerial vehicles (UAVs) are described. Special attention is paid to data processing algorithms, including spectral indexes, machine learning methods, and neural network models. The capabilities of the software (Google Earth Engine, SNAP, ArcGIS, QGIS) in mapping and monitoring tasks are analyzed. The review highlights the potential of remote sensing in improving the accuracy of early flood warnings and laying the foundations for sustainable water risk management.
In the presented work, the main challenge of small hydropower plants—converting low river flow velocities into high generator rotations—is investigated. It was established that applying the flow acceleration effect during interaction with surfaces makes it possible to increase the power output of a small hydropower plant by up to 25%, which corresponds to the level of an innovative solution. Stationary flow amplifiers and their influence on the dynamic interaction of blades were studied. It was revealed that the use of the amplification effect in paired configurations contributes to achieving a multiplicative effect. The potential of small hydropower plants was analytically evaluated, taking into account their dimensions and gear systems. The study was carried out using the method of computational fluid dynamics (CFD), which enables the modeling of complex hydrodynamic processes. Based on the developed three-dimensional model of the object and its discretization into a computational mesh, boundary conditions were set, and the finite volume method was applied to solve the Navier–Stokes equations. To account for turbulent flows, the k-epsilon turbulence model was employed.