Hiroki Akasaka

Dr. Hiroki Akasaka

orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 January 2021 in Materials
Verified
Journal Article
Open access
PDF file
NONaoto Ohtake
Naoto Ohtake
MHMasanori Hiratsuka
Masanori Hiratsuka
KKKazuhiro Kanda
Kazuhiro Kanda
HAHiroki Akasaka
Hiroki Akasaka
MTMasanori Tsujioka
Masanori Tsujioka
HSHidetoshi Saitoh
Hidetoshi Saitoh
Diamond-like carbon (DLC) films have been extensively applied in industries owing to their excellent characteristics such as high hardness. In particular, there is a growing demand for their use as protective films for mechanical parts owing to their excellent wear resistance and low friction coefficient. DLC films have been deposited by various methods and many deviate from the DLC regions present in the ternary diagrams proposed for sp3 covalent carbon, sp2 covalent carbon, and hydrogen. Consequently, redefining the DLC region on ternary diagrams using DLC coatings for mechanical and electrical components is urgently required. Therefore, we investigate the sp3 ratio, hydrogen content, and other properties of 74 types of amorphous carbon films and present the classification of amorphous carbon films, including DLC. We measured the sp3 ratios and hydrogen content using near-edge X-ray absorption fine structure and Rutherford backscattering-elastic recoil detection analysis under unified conditions. Amorphous carbon films were widely found with nonuniform distribution. The number of carbon atoms in the sp3 covalent carbon without bonding with hydrogen and the logarithm of the hydrogen content were inversely proportional. Further, we elucidated the DLC regions on the ternary diagram, classified the amorphous carbon films, and summarized the characteristics and applications of each type of DLC.

1 May 2021 in Materials
Verified
Journal Article
Open access
PDF file
MTMasashi Tomidokoro
Masashi Tomidokoro
STSarayut Tunmee
Sarayut Tunmee
URUkit Rittihong
Ukit Rittihong
CEChanan Euaruksakul
Chanan Euaruksakul
RSRatchadaporn Supruangnet
Ratchadaporn Supruangnet
HAHiroki Akasaka
Hiroki Akasaka
Hydrogenated amorphous carbon (a-C:H) films have optical and electrical properties that vary widely depending on deposition conditions; however, the electrical conduction mechanism, which is dependent on the film structure, has not yet been fully revealed. To understand the relationship between the film structure and electrical conduction mechanism, three types of a-C:H films were prepared and their film structures and electrical properties were evaluated. The sp2/(sp2 + sp3) ratios were measured by a near-edge X-ray absorption fine structure technique. From the conductivity–temperature relationship, variable-range hopping (VRH) conduction was shown to be the dominant conduction mechanism at low temperatures, and the electrical conduction mechanism changed at a transition temperature from VRH conduction to thermally activated band conduction. On the basis of structural analyses, a model of the microstructure of a-C:H that consists of sp2 and sp3-bonded carbon clusters, hydrogen atoms and dangling bonds was built. Furthermore, it is explained how several electrical conduction parameters are affected by the carrier transportation path among the clusters.

3 February 2021 in Materials
Verified
Journal Article
Open access
PDF file
YHYuki Hirata
Yuki Hirata
RTRyotaro Takeuchi
Ryotaro Takeuchi
HTHiroyuki Taniguchi
Hiroyuki Taniguchi
MKMasao Kawagoe
Masao Kawagoe
YIYoshinao Iwamoto
Yoshinao Iwamoto
NONaoto Ohtake
Naoto Ohtake
Amorphous boron carbon nitride (a-BCN) films exhibit excellent properties such as high hardness and high wear resistance. However, the correlation between the film structure and its mechanical properties is not fully understood. In this study, a-BCN films were prepared by an arc-sputtering hybrid process under various coating conditions, and the correlations between the film’s structure and mechanical properties were clarified. Glow discharge optical emission spectroscopy, X-ray photoelectron spectroscopy, Fourier-transform infrared spectroscopy, and Raman spectroscopy were used to analyze the structural properties and chemical composition. Nanoindentation and ball-on-disc tests were performed to evaluate the hardness and to estimate the friction coefficient and wear volume, respectively. The results indicated that the mechanical properties strongly depend on the carbon content in the film; it decreases significantly when the carbon content is <90%. On the other hand, by controlling the contents of boron and nitrogen to a very small amount (up to 2.5 at.%), it is possible to synthesize a film that has nearly the same hardness and friction coefficient as those of an amorphous carbon (a-C) film and better wear resistance than the a-C film.

1 March 2008 in Japanese Journal of Applied Physics
Verified
Journal Article
Closed access
HAHiroki Akasaka
Hiroki Akasaka
KIKoji Inazu
Koji Inazu
NONaoto Ohtake
Naoto Ohtake

12 August 2023 in Ceramics International
Verified
Journal Article
Closed access
NZNur Aszreen Zulkifli
Nur Aszreen Zulkifli
SLShahira LIZA
Shahira LIZA
HAHiroki Akasaka
Hiroki Akasaka
KFKanao Fukuda
Kanao Fukuda
NRNur Adilah Mohd Rawian
Nur Adilah Mohd Rawian
YYYazid Yaakob
Yazid Yaakob

29 April 2021 in Materials
Verified
Journal Article
Open access
PDF file
YLYUCHENG LI
YUCHENG LI
JEJun Enomoto
Jun Enomoto
YHYuki Hirata
Yuki Hirata
HAHiroki Akasaka
Hiroki Akasaka
NONaoto Ohtake
Naoto Ohtake
Diamond-like carbon (DLC) films have attracted considerable interest for application as protective films in diverse industrial parts. This is attributed to their desirable characteristics, such as high hardness, low coefficient of friction, gas-barrier properties, and corrosion resistance. Antiseizure properties, in addition to wear resistance, are required during the die molding of polymer and polymer-matrix composite parts. Graphite films can be easily peeled because the vertically stacked graphene sheets are bonded via weak van der Waals forces. The present study demonstrates the fabrication of multilayered DLC/Cu films, where the Cu film functions as a catalyst for the formation of a graphite-like layer between the DLC and Cu films. The DLC/Cu film was synthesized on a Si (100) substrate via plasma-enhanced chemical vapor deposition and magnetron sputtering. The peelability, wear resistance, microstructure, texture, and cross-section of the film were experimentally analyzed. The results indicated a variation in the peelability with the deposition conditions of the Cu film that comprised particles with diameters of several nanometers. The DLC film at the interface in contact with the Cu film was transformed into a graphite-like state i.e., graphitized. The surface of the multilayered film exhibited antiseizure properties with the peeling of the upper DLC film. The multilayered film also exhibited wear resistance owing to the repeated appearances of a new DLC film. It is expected that the wear-resistant films with antiseizure properties demonstrated in the present study will be utilized in various industrial sectors.