István Oldal

Dr. István Oldal

Hungarian University of Agriculture and Life Sciences
orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2012 in Advanced Powder Technology
Verified
Journal Article
Closed access
IOIstván Oldal
István Oldal
IKIstván Keppler
István Keppler
BCBela Csizmadia
Bela Csizmadia
LFLaszlo Fenyvesi
Laszlo Fenyvesi

13 July 2023 in Polymers
Verified
Journal Article
Open access
PDF file
Rawabe Fatima FaidallahRawabe Fatima Faidallah
Rawabe Fatima Faidallah
Muammel M. HanonMuammel M. Hanon
Muammel M. Hanon
VVVarun Vashist
Varun Vashist
AHAhmad Habib
Ahmad Habib
ZSZoltán Szakál
Zoltán Szakál
IOIstván Oldal
István Oldal
This study presents a comparative analysis of the tensile properties of 3D-printed polymer specimens with different standard geometry shapes. The objective is to assess the influence of printing orientation and geometry on the mechanical performance. Rectangular-shaped ASTM D3039 specimens with angles of 0°, 15°, and 90° are compared to various tensile test specimens based on ASTM and ISO standards. All specimens are fabricated using polyethylene terephthalate glycol (PETG) material through fused deposition modeling (FDM). Two printing orientations, flat and on-edge, are investigated, and tensile strength, elastic modulus, strain, and elongation at break are measured. The study examines the weak spot commonly found at the neck of the specimens and evaluates the broken areas. Additionally, a numerical analysis using the finite element method (FEM) is performed to identify stress risers’ locations in each specimen type. Experimental results show that the ASTM D3039-0° specimen printed in the on-edge orientation exhibits the highest tensile properties, while the flat orientation yields the best results in terms of the broken area. The ISO 527-2 specimens consistently display lower tensile properties, irrespective of the printing orientation. The study highlights the enhanced tensile properties achieved with the rectangular shape. Specifically, the tensile strength of ASTM D3039-0° was 17.87% and 21% higher than that of the ISO 527 geometry shape for the flat and on-edge orientations, respectively. The numerical analysis indicated that the ISO 527-2 specimen had either no or minimal stress raisers, and the higher stresses observed in the narrow section were isolated from the gripping location. The findings contribute to understanding the relationship between standard geometry shapes, printing orientation, and the resulting tensile properties of 3D-printed polymer specimens.

1 November 2012 in Advanced Powder Technology
Verified
Journal Article
Closed access
IKIstvan Keppler
Istvan Keppler
LKLaszlo Kocsis
Laszlo Kocsis
IOIstván Oldal
István Oldal
IFIstvan Farkas
Istvan Farkas
ACAttila Csatar
Attila Csatar

10 December 2021 in Journal of Polymer Engineering
Verified
Journal Article
Closed access
JDJózsef Dobos
József Dobos
Muammel M. HanonMuammel M. Hanon
Muammel M. Hanon
IOIstván Oldal
István Oldal
Three-dimensional (3D) printing settings allow the existence of differently filled sections together within a piece. That means the use of inhomogeneous internal material structure. Knowing the load capacity that 3D printed plastic parts can withstand leads to the reduction of the filling degree, thus the amount of the used material in certain places. This approach has two advantages during production: (i) less material use and (ii) reduced manufacturing time, both being cost-reducing factors. The present research aims to find the optimal proportions for fabricating a bending test piece with varying filling degrees. To achieve this goal, experimental tests were performed for obtaining tensile strength and modulus of elasticity using different pairs of infill density and pattern. This provided a basis for creating a working mechanical model based on accurate and realistic material properties. Hence, a series of virtual bending test experiments were conducted on a sandwich structure specimen employing Ansys Workbench software. By doing so, the optimal thickness (of the sandwich’s inner layer) with the highest specific load capacity for the given filling patterns and densities were determined. To the best of our knowledge, the current procedure of experiments and method of settings optimization were not discussed elsewhere.

20 April 2015 in Engineering Computations
Verified
Journal Article
Closed access
IKIstvan Keppler
Istvan Keppler
ZHZoltan Hudoba
Zoltan Hudoba
IOIstván Oldal
István Oldal
ACAttila Csatar
Attila Csatar
LFLaszlo Fenyvesi
Laszlo Fenyvesi
Purpose: – The analysis of the effect of tool vibrations on the measured and simulated draught forces of cultivator tools. This paper aims to discuss this issue. Design/methodology/approach: – Soil bin measurements and discrete element method (DEM)-based simulations. Findings: – The soil-tool interaction induced free vibrations of cultivator tools have significant impact on the measured draught force, and the simulations made by using vibrating tools give similar results. Research limitations/implications: – Accurate calibration of discrete element model parameters can be done based on the reproduction of the whole Mohr-Coulomb failure line. Draught force ratio – velocity ratio values seem to be independent of tool geometry and soil conditions in case of velocity ratio higher than 2. Practical implications: – DEM-based numerical simulations can be used for modeling the effect of tool vibration on the draught force values. During discrete element simulations of soil-tool interaction, the effect of tool vibration may not be neglected. Originality/value: – The paper demonstrates that during the discrete element modelling of the soil-tool interaction, the tool vibration phenomenon should not be neglected.

12 September 2015 in Journal of Mechanical Science and Technology
Verified
Journal Article
Closed access
PDF file
IOIstván Oldal
István Oldal
FSFerenc Safranyik
Ferenc Safranyik