Varun Vashist

Mr. Varun Vashist


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 July 2023 in Polymers
Verified
Journal Article
Open access
PDF file
Rawabe Fatima FaidallahRawabe Fatima Faidallah
Rawabe Fatima Faidallah
Muammel M. HanonMuammel M. Hanon
Muammel M. Hanon
VVVarun Vashist
Varun Vashist
AHAhmad Habib
Ahmad Habib
ZSZoltán Szakál
Zoltán Szakál
IOIstván Oldal
István Oldal
This study presents a comparative analysis of the tensile properties of 3D-printed polymer specimens with different standard geometry shapes. The objective is to assess the influence of printing orientation and geometry on the mechanical performance. Rectangular-shaped ASTM D3039 specimens with angles of 0°, 15°, and 90° are compared to various tensile test specimens based on ASTM and ISO standards. All specimens are fabricated using polyethylene terephthalate glycol (PETG) material through fused deposition modeling (FDM). Two printing orientations, flat and on-edge, are investigated, and tensile strength, elastic modulus, strain, and elongation at break are measured. The study examines the weak spot commonly found at the neck of the specimens and evaluates the broken areas. Additionally, a numerical analysis using the finite element method (FEM) is performed to identify stress risers’ locations in each specimen type. Experimental results show that the ASTM D3039-0° specimen printed in the on-edge orientation exhibits the highest tensile properties, while the flat orientation yields the best results in terms of the broken area. The ISO 527-2 specimens consistently display lower tensile properties, irrespective of the printing orientation. The study highlights the enhanced tensile properties achieved with the rectangular shape. Specifically, the tensile strength of ASTM D3039-0° was 17.87% and 21% higher than that of the ISO 527 geometry shape for the flat and on-edge orientations, respectively. The numerical analysis indicated that the ISO 527-2 specimen had either no or minimal stress raisers, and the higher stresses observed in the narrow section were isolated from the gripping location. The findings contribute to understanding the relationship between standard geometry shapes, printing orientation, and the resulting tensile properties of 3D-printed polymer specimens.

13 June 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
Rawabe Fatima FaidallahRawabe Fatima Faidallah
Rawabe Fatima Faidallah
Muammel M. HanonMuammel M. Hanon
Muammel M. Hanon
VVVarun Vashist
Varun Vashist
AHAhmad Habib
Ahmad Habib
ZSZoltán Szakál
Zoltán Szakál
IOIstván Oldal
István Oldal
The objective of this research is to conduct a comparative analysis between rectangular-shaped ASTM D3039 specimens with different angles (0°, 15°, and 90°) and various tensile test specimens based on ASTM and ISO standards, all 3D-printed using polyethylene terephthalate glycol (PETG) material through FDM. The study aimed to assesses the weak spot commonly found at the neck of the specimens. Two different printing orientations, namely flat and on-edge, were investigated, and a comprehensive examination and comparison were made regarding the variations in tensile strength, E-modulus, strain, and elongation at break among the tested samples. Additionally, the broken areas was evaluated, and a numerical study utilizing the finite element method (FEM) was conducted to identify stress risers' locations in each specimen type. The experimental results demonstrated that the ASTM D3039-0° specimen exhibited the best tensile properties when printed in the on-edge orientation, while the flat orientation yielded the best results in terms of the broken area. On the other hand, the ISO 527-2 specimens displayed the lowest tensile properties, regardless of the printing orientation. The study highlighted the enhanced tensile properties achieved with the rectangular shape. Specifically, the tensile strength of ASTM D3039-0° was 17.87% and 21% higher than that of the ISO 527 geometry shape for the flat and on-edge orientations, respectively. The numerical analysis indicated that the ISO 527-2 specimen had either no or minimal stress raisers, and the higher stresses observed in the narrow section were isolated from the gripping location.

16 September 2025 in Journal of Materials Engineering and Performance
Verified
Journal Article
Open access
PDF file
VVVarun Vashist
Varun Vashist
OIOldal Istvan
Oldal Istvan
ZSZoltan Szakal
Zoltan Szakal
This study presents a comprehensive investigation of process optimization and performance evaluation of Steel 1.2709 and Steel 1.4542 made from Selective Laser Melted (SLM) method. A Central Composite Face-Centered Design (CCFD) based on Response Surface Methodology (RSM) was employed to assess the effect of laser power (200-400 W) and scanning speed (800-1200 mm/s) on ultimate tensile strength (UTS) and impact toughness. Based on regression modeling and numerical optimization, the optimal parameter combination was determined as 234.80 W laser power and 912.52 mm/s scanning speed, which yielded superior mechanical performance for both steels. However, 1.2709 steel outperformed as compared to 1.4542 steel across all conditions. Fractographic analysis via SEM revealed ductile fracture modes in Steel 1.2709, while Steel 1.4542 exhibited ductile-brittle failure with intergranular cracking. Furthermore, slurry erosion behavior was examined under varying impact angles (30°, 60° and 90°) and erodent particle sizes (100-300 µm). Steel 1.2709 exhibited reduced erosion loss (i.e., 19.6 mg) relative to Steel 1.4542 (i.e., 23.2 mg), owing to its enhanced microstructural integrity and strain accommodation capabilities. Post-erosion SEM analysis confirmed distinct wear mechanisms, majorly plastic ploughing in 1.2709 and brittle pitting in 1.4542.

1 May 2023 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
VVVarun Vashist
Varun Vashist
IOI Oldal
I Oldal
ZSZ Szakal
Z Szakal
In our research work, we analyzed the mechanical properties of 3D-printed metallic specimens of aluminium bronze material. In our evaluation, we had five groups of specimens, manufactured at different laser scanning speeds. In total, we had 25 specimens for which we examined various parameters like ultimate tensile strength, engineering yield point, relative strain, and hardness. Results showed that specimens prepared with a lower laser scanning speed of 300mm/s showed the lowest tensile strength. The tensile strength increased with increasing laser scan speed and the highest tensile strength was attained by specimens of the fourth group that were produced at a laser scanning speed of 500mm/s. The relative strain of specimens also increased with the increasing scan speed of the laser. The Brinell hardness test also showed an elevation in hardness values with increasing laser scan speeds.

19 September 2024 in Preprints.org
Verified
Preprint
Open access
PDF file
VVVarun Vashist
Varun Vashist
IOIstván Oldal
István Oldal
RFRawabe Fatima Faidallah
Rawabe Fatima Faidallah
ZSZoltan Szakal
Zoltan Szakal
Process parameters influencing mechanical properties have always been a critical area of research for quite some time. We investigated the effect of laser power and laser scan velocity on the impact strength and maximum stress of 3D-printed metallic specimens of steel 1.2709 and 1.4542. Laser power significantly affected the impact strength and maximum stress of both the steels. With the increase in laser power, the impact strength increased for 1.2709 steel. However, there was a little increase in the impact strength with increasing laser power in the case of 1.4542 steel. Laser power had a decreasing impact on the maximum stress for 1.2709 steel. For 1.4542, maximum stress increased with increasing laser power, but then gradually declined. We observed that using laser power beyond 350W led to printing defect in the specimens, as maximum stress for some specimens reached close to zero in the case of 1.4542 steel. Laser scan velocity had a strong declining effect on the impact strength of 1.2709 steel.