Rawabe Fatima Faidallah

Dr. Rawabe Fatima Faidallah


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 July 2023 in Polymers
Verified
Journal Article
Open access
PDF file
Rawabe Fatima FaidallahRawabe Fatima Faidallah
Rawabe Fatima Faidallah
Muammel M. HanonMuammel M. Hanon
Muammel M. Hanon
VVVarun Vashist
Varun Vashist
AHAhmad Habib
Ahmad Habib
ZSZoltán Szakál
Zoltán Szakál
IOIstván Oldal
István Oldal
This study presents a comparative analysis of the tensile properties of 3D-printed polymer specimens with different standard geometry shapes. The objective is to assess the influence of printing orientation and geometry on the mechanical performance. Rectangular-shaped ASTM D3039 specimens with angles of 0°, 15°, and 90° are compared to various tensile test specimens based on ASTM and ISO standards. All specimens are fabricated using polyethylene terephthalate glycol (PETG) material through fused deposition modeling (FDM). Two printing orientations, flat and on-edge, are investigated, and tensile strength, elastic modulus, strain, and elongation at break are measured. The study examines the weak spot commonly found at the neck of the specimens and evaluates the broken areas. Additionally, a numerical analysis using the finite element method (FEM) is performed to identify stress risers’ locations in each specimen type. Experimental results show that the ASTM D3039-0° specimen printed in the on-edge orientation exhibits the highest tensile properties, while the flat orientation yields the best results in terms of the broken area. The ISO 527-2 specimens consistently display lower tensile properties, irrespective of the printing orientation. The study highlights the enhanced tensile properties achieved with the rectangular shape. Specifically, the tensile strength of ASTM D3039-0° was 17.87% and 21% higher than that of the ISO 527 geometry shape for the flat and on-edge orientations, respectively. The numerical analysis indicated that the ISO 527-2 specimen had either no or minimal stress raisers, and the higher stresses observed in the narrow section were isolated from the gripping location. The findings contribute to understanding the relationship between standard geometry shapes, printing orientation, and the resulting tensile properties of 3D-printed polymer specimens.

6 March 2025 in International Review of Applied Sciences and Engineering
Verified
Journal Article
Open access
PDF file
Rawabe Fatima FaidallahRawabe Fatima Faidallah
Rawabe Fatima Faidallah
Muammel M. HanonMuammel M. Hanon
Muammel M. Hanon
ZSZoltán Szakál
Zoltán Szakál
IOIstván Oldal
István Oldal
Fused deposition modeling (FDM) 3D printing is widely utilized for producing thermoplastic components with functional purposes. However, the inherent mechanical limitations of pure thermoplastic materials necessitate enhancements in their mechanical characteristics when employed in certain applications. One strategy for addressing this challenge involves the incorporation of reinforcement materials, such as carbon fiber (CF), within the thermoplastic matrix. This approach leads to the creation of carbon fiber-reinforced polymer composites (CFRPs) suitable for engineering applications. The utilization of CFRPs in 3D printing amalgamates the benefits of additive manufacturing, including customization, cost-effectiveness, reduced waste, swift prototyping, and accelerated production, with the remarkable specific strength of carbon fiber. This study encompasses tensile and compressive testing of distinct material compositions: recycled polylactic acid (rPLA), PLA enriched with 10 wt.% carbon fiber, pristine polyethylene terephthalate glycol (PETG), and PETG bolstered with 10 wt.% carbon fiber. Tensile tests adhere to the ASTM D3039 standard for specimens of rectangular shape, while the ASTM D695 standard governs the compressive testing procedures. Additionally, an inquiry into the influence of the primary 3D printing build orientation parameter on the tensile and compressive strengths of diverse materials was conducted. The outcomes reveal that rPLA exhibits superior mechanical properties in both tensile and compressive tests, irrespective of flat or on-edge build orientations. In the context of tensile strength analysis, it is noteworthy that rPLA demonstrated a superior performance, surpassing CFPLA by 30% in flat orientation and exhibiting a remarkable 39.2% advantage in on-edge orientation. Moreover, PLA reinforced with carbon fiber exhibits superior tensile and compressive properties compared to its PETG counterpart. A comparative analysis between CFPLA and CF-PETG indicates that CF-PLA demonstrates higher tensile strengths, with increases of 26.6 and 27.6% for flat and on-edge orientations, respectively. In the context of compressive strength analysis, rPLA surpassed CFPLA, PETG, and CF-PETG by 23.7, 53, and 67%, respectively. Intriguingly, the findings indicate that the incorporation of 10 wt.% carbon fiber diminishes the tensile and compressive properties in comparison to pure PETG.

11 October 2024 in Processes
Verified
Journal Article
Open access
PDF file
Rawabe Fatima FaidallahRawabe Fatima Faidallah
Rawabe Fatima Faidallah
Muammel M. HanonMuammel M. Hanon
Muammel M. Hanon
NSNihal Salman
Nihal Salman
YIYousef Ibrahim
Yousef Ibrahim
MBMd. Noman Babu
Md. Noman Babu
IOIstván Oldal
István Oldal
This study investigates the mechanical properties of carbon and natural fiber-reinforced Polylactic Acid (PLA) and Polyethylene Terephthalate Glycol (PETG) composites produced via Additive Manufacturing (AM), focusing on Material Extrusion (MEX). The performance of filaments made from pre-consumer recycled PLA (rPLA) and PETG, with varying weight percentages of hemp and jute short fibers, was evaluated through tensile testing. Comparisons were made between the original filaments (PLA, carbon fiber-reinforced PLA [CF–PLA], and PETG) and their recycled versions. Multi-material compositions—neat PLA and PETG, single-graded (PLA + CF–PLA, PETG + CF–PETG), and multi-gradient (PLA + CF–PLA + PLA, PETG + CF–PETG + PETG)—were analyzed for mechanical properties. Optical microscope images of multi-material specimens were captured before and after fracture to assess failure mechanisms. The results indicate that the original CF–PETG filaments achieved a tensile strength of 50.14 MPa, which is higher than rPLA, PLA, and CF–PLA by 2%, 70%, and 6.7%, respectively. The re-manufactured PLA filaments reinforced with 7 wt% hemp fibers exhibited a tensile strength of 38.8 MPa, representing a 29% increase compared to the original PLA filaments and a 26% improvement over recycled PLA. Additionally, incorporating 7% jute fiber into PETG resulted in a tensile strength of 62.38 MPa, reflecting a 12% improvement over the original PETG filaments and a 15% increase compared to the recycled PETG filaments. Among specimens produced by AM, CF–PLA and rPLA demonstrated the highest tensile and compressive strengths. However, multi-material composites showed reduced mechanical performance compared to neat PLA and PETG, highlighting the need for improved interlayer adhesion. This study emphasizes the importance of optimizing material combinations and fiber reinforcement to enhance the mechanical properties of composites produced through AM.

13 June 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
Rawabe Fatima FaidallahRawabe Fatima Faidallah
Rawabe Fatima Faidallah
Muammel M. HanonMuammel M. Hanon
Muammel M. Hanon
VVVarun Vashist
Varun Vashist
AHAhmad Habib
Ahmad Habib
ZSZoltán Szakál
Zoltán Szakál
IOIstván Oldal
István Oldal
The objective of this research is to conduct a comparative analysis between rectangular-shaped ASTM D3039 specimens with different angles (0°, 15°, and 90°) and various tensile test specimens based on ASTM and ISO standards, all 3D-printed using polyethylene terephthalate glycol (PETG) material through FDM. The study aimed to assesses the weak spot commonly found at the neck of the specimens. Two different printing orientations, namely flat and on-edge, were investigated, and a comprehensive examination and comparison were made regarding the variations in tensile strength, E-modulus, strain, and elongation at break among the tested samples. Additionally, the broken areas was evaluated, and a numerical study utilizing the finite element method (FEM) was conducted to identify stress risers' locations in each specimen type. The experimental results demonstrated that the ASTM D3039-0° specimen exhibited the best tensile properties when printed in the on-edge orientation, while the flat orientation yielded the best results in terms of the broken area. On the other hand, the ISO 527-2 specimens displayed the lowest tensile properties, regardless of the printing orientation. The study highlighted the enhanced tensile properties achieved with the rectangular shape. Specifically, the tensile strength of ASTM D3039-0° was 17.87% and 21% higher than that of the ISO 527 geometry shape for the flat and on-edge orientations, respectively. The numerical analysis indicated that the ISO 527-2 specimen had either no or minimal stress raisers, and the higher stresses observed in the narrow section were isolated from the gripping location.