Markus Baumann

Mr. Markus Baumann

Technische Universität Chemnitz
orcid

Research Focus & Metrics

Academic Career Length

29Years (1998-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 April 2021 in Materials
Verified
Journal Article
Open access
PDF file
MBMarkus Baumann
Markus Baumann
RSRené Selbmann
René Selbmann
MMMatthias Milbrandt
Matthias Milbrandt
VKVerena Kräusel
Verena Kräusel
MBMarkus Bergmann
Markus Bergmann
After conventional forming processes, the residual stress distribution in wires is frequently unfavorable for subsequent processes, such as bending operations. High tensile residual stresses typically occur near the wire surface and normally limit further processability of the material. Additional heat treatment operations or shot peening are often used to influence the residual stress distribution in the material after conventional manufacturing, which is time- and energy-consuming. This paper presents an approach for influencing the residual stress distribution by modifying the forming process, especially regarding die geometry. The aim is to reduce the resulting tensile stress levels near the surface. Specific forming elements are integrated into the dies to achieve this residual stress reduction. These modifications in the forming zone have a significant influence on process properties, such as plastic strain and deformation direction, but typically do not influence product geometry. This paper describes the theoretical approach and model setup, the FE simulation, and the results of the experimental tests. The characterization of the residual stress states in the specimen was carried out through X-ray diffraction using the sin2Ψ method.

18 September 2018 in MATEC Web of Conferences
Verified
Journal Article
Open access
MBMarkus Baumann
Markus Baumann
AGAlexander Graf
Alexander Graf
RSRené Selbmann
René Selbmann
KBKatrin Brömmelhoff
Katrin Brömmelhoff
VKVerena Kräusel
Verena Kräusel
MBMarkus Bergmann
Markus Bergmann
Torsion bars are used in automotive engineering as well as in other industrial applications. Such elements are produced by bending cold drawn wires. In conventional drawing processes tensile residual stresses occur near the surface of the wire. Small bending radii, which are required in limited assembly spaces, result in component failure due to reduced formability. Additional operations such as heat treatment or shot peening are necessary to influence the residual stress of the wire and to improve the dynamic stability of the torsion bar. The aim of the research is to reduce tensile residual stresses near the surface of the wire in order to eliminate process steps and to enhance formability. Therefore, a forming technology is developed by using a modified drawing die geometry on the basis of gradation extrusion. Finite element simulation is used to investigate the influences of element geometry, number of elements and process modification on the resulting residual stresses after wire drawing of a steel alloy. The results are evaluated and compared with the conventional wire drawing process. Furthermore, the requirements for the design of an experimental test device will be outlined as well as the measurement of the residual stresses by using X-ray diffraction.

14 July 2021 in Forschung im Ingenieurwesen
Verified
Journal Article
Open access
PDF file
MBMarkus Baumann
Markus Baumann
RSRené Selbmann
René Selbmann
MDMateus Dobecki
Mateus Dobecki
VKVerena Kräusel
Verena Kräusel
WRWalter Reimers
Walter Reimers
MBMarkus Bergmann
Markus Bergmann
Zusammenfassung: Nach dem Drahtziehen treten hohe Zugeigenspannungen in den oberflächennahen Schichten des Drahtes auf. Dieser Eigenspannungszustand ist für die weitere umformtechnische Verarbeitung, z. B. für das Biegen zur Herstellung von Torsionstabfedern, ungeeignet. Nach derzeitigen Standards wird dem Drahtziehen eine Wärmebehandlung nachgeschaltet. In diesem Artikel wird ein neuer Ansatz zur Einstellung des Eigenspannungszustandes direkt im Umformprozess des Drahtes vorgestellt. Durch eine Modifikation der Ziehwerkzeuge mit integrierten Umformelementen sollen niedrigere Zugspannungsniveaus in den oberflächennahen Schichten des Drahtes erzeugt werden. Diese Elemente haben wesentlichen Einfluss auf den Grad der Kaltverfestigung, ohne den Drahtdurchmesser zu verändern. Zunächst werden mittels FE-Simulationen verschiedene Werkzeuggeometrien hinsichtlich ihrer Wirkung auf den Umformgrad sowie den Eigenspannungszustand des gezogenen Drahtes analysiert und bewertet. Durch den Einsatz eines speziell konzipierten Drahtziehwerkzeugs werden experimentelle Versuche durchgeführt und Drahtproben erzeugt. Weiterhin wird die Vorgehensweise für die Messung der Eigenspannungen durch den Einsatz von Röntgenbeugung erläutert. Für weiterführende experimentelle Untersuchungen zum Biegen erfolgte die Konzipierung eines modularen Werkzeuges, das eine Variation der Biegeradien und Drahtdurchmesser ermöglicht.

1 January 1998
Verified
Conference Paper
Closed access
MBMarkus Baumann
Markus Baumann
MRM. Rohner
M. Rohner
KDK.M. Du
K.M. Du
PLP. Loosen
P. Loosen
RPR. Poprawe
R. Poprawe
Fulltext: Because of the asymmetric emission characteristics of high-power diode laser bars, beam shaping is essential for coupling the light into a fibre. Preservation of the high brightness is the crucial point for minimum core diameter and NA. The radiation of two high-power diode laser bars is collimated in fast-axis direction by microlenses and polarisation multiplexed. A telecentric optics, mainly consisting of a concave and a convex mirror (Offner configuration) images the emitters on the retroreflecting mirrors. The surface of these mirrors consists of right angle v-grooves, whose pitch is matched to the emitter pitch of the diode laser. They are aligned at 45 degree in respect to the fast-axis direction of the incident beam. Therefore each image of an emitter is rotated by 90 degree when it is reflected from one side of a groove to the other. In the emerging beam after beam shaping the emitters are arranged in fast-axis direction. A polarisation beam splitter deflects the emer ging beam out of the incident-beam direction. The fast-axis is recollimated with a lenticular lens at the position, where maximum filling factor is obtained. A set of lenses couples the light into the fibre. As a result a spot size of less than 160 mu m to 80 mu m at NA 0.2 was achieved with a prototype setup. With the appropriate coatings a power transmission efficiency of more than 70 per cent is expected