A single-photon avalanche diode (SPAD) with enhanced near-infrared (NIR) sensitivity has been developed, based on 0.18 μm CMOS technology, for use in future automotive light detection and ranging (LIDAR) systems. The newly proposed SPAD operating in Geiger mode achieves a high NIR photon detection efficiency (PDE) without compromising the fill factor (FF) and a low breakdown voltage of approximately 20.5 V. These properties are obtained by employing two custom layers that are designed to provide a full-depletion layer with a high electric field profile. Experimental evaluation of the proposed SPAD reveals an FF of 33.1% and a PDE of 19.4% at 870 nm, which is the laser wavelength of our LIDAR system. The dark count rate (DCR) measurements shows that DCR levels of the proposed SPAD have a small effect on the ranging performance, even if the worst DCR (12.7 kcps) SPAD among the test samples is used. Furthermore, with an eye toward vehicle installations, the DCR is measured over a wide temperature range of 25–132 °C. The ranging experiment demonstrates that target distances are successfully measured in the distance range of 50–180 cm.
A CMOS light pulse receiver (LPR) cell for spatial optical communications is designed and evaluated by device simulations and a prototype chip implementation. The LPR cell consists of a pinned photodiode and four transistors. It works under sub-threshold region of a MOS transistor and the source terminal voltage which responds to the logarithm of the photo current are read out with a source follower circuit. For finding the position of the light spot on the focal plane, an image pixel array is embedded on the same plane of the LPR cell array. A prototype chip with 640 × 240 image pixels and 640 × 240 LPR cells is implemented with 0.18 μm CMOS technology. A proposed model of the transient response of the LPR cell agrees with the result of the device simulations and measurements. Both imaging at 60 fps and optical communication at the carrier frequency of 1 MHz are successfully performed. The measured signal amplitude and the calculation results of photocurrents show that the spatial optical communication up to 100 m is feasible using a 10 × 10 LED array.
As automotive safety systems advance, the number of in-vehicle cameras continues to increase, placing a growing burden on their integration. Simple low-cost methods for acquiring scene images are thus required. Direct image transmission via a single multimode fiber is a candidate for next-generation automotive image networks. Most conventional approaches rely on complex and fragile optics and laser sources, which are undesirable for automotive use. We propose a streamlined and fully passive architecture that relies solely on lenses, a plastic optical fiber (POF), an image sensor, and an image reconstruction network, and show that this method enables simultaneous multi-directional scene acquisition with a single sensor. We systematically evaluate image reconstruction performance under a variety of real-world automotive conditions. Color image transmission through POFs of various lengths (0.1–10 m) is demonstrated. High robustness against bending (2–10 cm radius), twisting (1–4 turns), and temperature variations (15–45 °C) is shown. These findings offer key insights toward deployment of streamlined POF-based direct image transmission in automotive applications and other fields.
Conventional image acquisition requires an electrically powered image sensor to be placed directly behind the camera lens, constraining camera placement. To overcome this issue, we introduce M3-RGB as an incoherent-light fiber imaging system in which a multi-core, multi-mode optical fiber passively relays lens images to a remotely located image sensor. Unlike conventional approaches, M3-RGB is designed to operate directly on incoherent light and requires no electrical power or active components at the sensing interface. Because propagation through the fiber yields spatially scrambled patterns, a neural network is used to reconstruct the original scene by exploiting the spatial locality preserved by the multi-core structure. In a controlled optical bench setup, where an LCD monitor displays road-scene images, we construct a paired dataset of scrambled and ground-truth images and quantitatively evaluate reconstruction performance across different fiber core counts, fiber lengths, and calibration settings, utilizing the peak signal-to-noise ratio and structural similarity index measure as performance metrics. By decoupling imaging electronics from the sensing point, this passive remote image relay approach may expand sensor placement options for potential applications such as all-around perception for mobile robots and autonomous vehicles, surveillance, and inspection in confined spaces. Evaluations in real outdoor environments remain targets for future work.
Conventional image acquisition requires an electrically powered image sensor to be placed directly behind the camera lens, constraining camera placement. To overcome this issue, we introduce M3-RGB as an incoherent-light fiber imaging system in which a multicore, multimode optical fiber passively relays lens images to a remotely located image sensor. Unlike conventional approaches, M3-RGB is designed to operate directly on incoherent light and requires no electrical power or active components at the sensing interface. Because propagation through the fiber yields spatially scrambled patterns, a neural network is used to reconstruct the original scene by exploiting the spatial locality preserved by the multicore structure. In a controlled optical bench setup, where a liquid crystal display monitor displays road-scene images, we construct a paired dataset of scrambled and ground-truth images and quantitatively evaluate reconstruction performance across different fiber core counts, fiber lengths, and calibration settings, utilizing the peak signal-to-noise ratio and structural similarity index measure as performance metrics. By decoupling imaging electronics from the sensing point, this passive remote image relay approach may expand sensor placement options for potential applications such as all-around perception for mobile robots and autonomous vehicles, surveillance, and inspection in confined spaces. Evaluations in real outdoor environments constitute future work.
As automotive safety systems advance, the number of in-vehicle cameras continues to increase, placing a growing burden on their integration. Simple low-cost methods for acquiring scene images are thus required. Direct image transmission via a single multimode fiber is a candidate for next-generation automotive image networks. Most conventional approaches rely on complex and fragile optics and laser sources, which are undesirable for automotive use. We propose a streamlined and fully passive architecture that relies solely on lenses, a plastic optical fiber (POF), an image sensor, and an image reconstruction network, and show that this method enables simultaneous multi-directional scene acquisition with a single sensor. We systematically evaluate image reconstruction performance under a variety of real-world automotive conditions. Color image transmission through POFs of various lengths (0.1 to 10 m) is demonstrated. High robustness against bending (2 to 10 cm radius), twisting (1 to 4 turns), and temperature variations (15 to 45 °C) is shown. These findings offer key insights toward real-world implementation of streamlined POF-based direct image transmission in automotive applications and other fields.