Rigid polyurethane foams are the better-performing material for the most common insulation purposes, like sandwich panels. Nevertheless, they are highly flammable materials, release toxic gases, and are manufactured from fossil sources. As an alternative, tannin foams are bio-based materials that work as innovative alternatives thanks to their great fire resistance, as well as lower smoke and harmful gases emissions. In the present study, lab-made foams of both materials were compared through morphology, thermal and fire degradation, mechanical properties, and water affinity in order to fill the technological gap between them and their related sandwich panels. It was observed that tannin foams are still relatively inhomogeneous (since formaldehyde was not used) and present a high affinity for water but have higher thermal and fire resistance. The flat compression strength of the polyurethane sandwiches was greater than that of tannin sandwiches (3.61 and 3.09 MPa, respectively) thanks, mainly, to the crosslinking degree difference between the resins. Also, tannin foams presented a lower weight loss (−70.684% lower weight loss in flammability tests than polyurethane foams) and the ability to self-extinguish the flame. Therefore, sandwich panels with tannin foam cores could be successful materials in areas that require protection against fire, such as the building engineering and automotive industries.

Aerogels are 3-D nanostructures of non-fluid colloidal interconnected porous networks consisting of loosely packed bonded particles that are expanded throughout their volume by gas and exhibit ultra-low density and high specific surface area. Cellulose-based aerogels can be obtained from hydrogels through a drying process, replacing the solvent (water) with air and keeping the pristine three-dimensional arrangement. In this work, hybrid cellulose-based aerogels were produced and their potential for use as dressings was assessed. Nanofibrilated cellulose (NFC) hydrogels were produced by a co-grinding process in a stone micronizer using a kraft cellulosic pulp and a phenolic extract from Maclura tinctoria (Tajuva) heartwood. NFC-based aerogels were produced by freeze followed by lyophilization, in a way that the Tajuva extract acted as a functionalizing agent. The obtained aerogels showed high porosity (ranging from 97% to 99%) and low density (ranging from 0.025 to 0.040 g·cm⁻³), as well a typical network and sheet-like structure with 100 to 300 μm pores, which yielded compressive strengths ranging from 60 to 340 kPa. The reached antibacterial and antioxidant activities, percentage of inhibitions and water uptakes suggest that the aerogels can be used as fluid absorbers. Additionally, the immobilization of the Tajuva extract indicates the potential for dentistry applications.

O crescente interesse mundial na polpa celulósica produzida a partir da madeira de Acacia mearnsii incentiva estudos que comprovem sua propensão e eficiência para esse fim. Dessa forma, o objetivo deste estudo foi avaliar as propriedades físico-químicas da madeira de Acacia mearnsii, bem como avaliar seu desempenho na produção de celulose kraft, sob diferentes condições de cozimento. Amostras de madeiras das áreas de produção de sementes (APS) e clones foram avaliados. A polpação kraft foi realizada com fator H constante (1363) e álcali ativo variando de 14% a 24%. A densidade básica das madeiras de clone e APS não diferiram estatisticamente (0,544 g/cm³). A análise química revelou que o conteúdo médio (clone e APS) de extrativos, lignina e carboidratos foi de 4,67%, 16,66% e 77,02%, respectivamente. A condição de polpação mais eficiente foi obtida com álcali ativo de 14%, número kappa 16 e rendimento depurado de 57%. De acordo com os resultados, a madeira de Acacia mearnsii apresentou grande potencial para ser utilizada como fonte de fibra curta na obtenção de polpa celulósica pelo processo kraft.

Thermal treatments arise as an alternative to increase the physical and biological properties of wood, though they usually cause a reduction in mechanical strength. Therefore, the aim of the study was to determine the brittleness of Eucalyptus wood submitted to freezing and heat treatments. Freezing occurred with green condition specimens and the heat treatment with samples in equilibrium moisture content (20°C and 65% RH). The static bending test was carried out on an EMIC® universal testing machine. The freezing showed slight changes in the mechanical properties of Eucalyptus wood, not differing from natural wood. The treatments with high temperatures caused significant losses in mechanical strength, evidenced by decreases in maximum load and increases in brittleness. In the combined treatments, there was no sum of effects. Therefore, heat treatments modify the mechanical properties of wood, increasing its brittleness and following the tendency that, as the temperature increases, the mechanical resistance decreases.

Flame-resistant materials are key components in buildings and several other engineering applications. In this study, flame retardancy and thermal stability were conferred to a highly flammable technical thermoplastic—polypropylene (PP)—upon compositing with a carbonaceous tannin-based particulate (CTP). Herein, we report on a straightforward, facile, and green approach to prepare self-extinguishing thermoplastic composites by thermoblending highly recalcitrant particulate. The thermal stability and mechanical properties of the composites are tethered to the CTP content. We demonstrate that the addition of up to 65 wt% of CTP improved the viscoelastic properties and hydrophobicity of the PP, whereas having marginal effects on bulk water interactions. Most importantly, compositing with CTP remarkably improved the thermal stability of the composites, especially over 300 °C, which is an important threshold associated with the combustion of volatiles. PP-CTP composites demonstrated great capacity to limit and stop fire propagation. Therefore, we offer an innovative route towards thermally resistant and self-extinguishing PP composites, which is enabled by sustainable tannin-based flame retardants capable of further broadening the technical range of commodity polyolefins to high temperature scenarios.

Maclura tinctoria is a tree species native from Brazil and rich in phenolic compounds. Since plant antibacterial activity is highly associated with phenolic compound concentration, we aim to evaluate the in vitro antimicrobial activity of different extracts against fish pathogenic bacteria. In addition, some phenolic compounds have central depressant effects and can be useful in aquaculture due to possible sedative and/or anesthetic effects. Four M. tinctoria extracts were extracted separately with ethanol; leaves (LE), bark (BE), heartwood (HE), and the sapwood (SE). In vitro antimicrobial activity was tested against Aeromonas strains at concentrations of 6400 to 3.125 μg/mL. The sedative effect was evaluated for 24 h with 30 and 100 mg/L concentrations. Chemical composition was analyzed by HPLC-DAD-MS. The HE extract had the best MIC (400 µg/mL) and MBC (800 µg/mL) compared to the LE, BE, and SE extracts. LE extract induced deep sedation and the BE, SE, and HE extracts induced light sedation. Additionally, BE, SE, and HE induced a normal behavior without side effects. Polyphenolic compounds with antimicrobial activity and sedative effects were identified mainly in HE. Thus, HE extract is safe and can be used as a sedative for silver catfish.