Seong Gwan Shin

Dr. Seong Gwan Shin

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 April 2021 in Nanomaterials
Verified
Journal Article
Open access
PDF file
SSSeong Gwan Shin
Seong Gwan Shin
CBChung Wung Bark
Chung Wung Bark
HCHyung Wook Choi
Hyung Wook Choi
In this study, a simply structured perovskite-based ultraviolet C (UVC) sensor was prepared using a one-step, low-temperature solution-processing coating method. The UVC sensor utilized CH3NH3PbBr3 perovskite as the light-absorbing layer. To improve the characteristics of CH3NH3PbBr3, an antisolvent process using toluene and the addition of CH3NH3Cl were introduced. The device with these modifications exhibited a response rise/fall time of 15.8/16.2 ms, mobility of 158.7 cm2/V·s, responsivity of 4.57 mA/W, detectivity of 1.02 × 1013 Jones, and external quantum efficiency of 22.32% under the 254-nm UV illumination. Therefore, this methodology could be a good approach in facilitating UVC detection.

4 February 2022 in Coatings
Verified
Journal Article
Open access
PDF file
YKYujin Kim
Yujin Kim
SJSung Hwan Joo
Sung Hwan Joo
SSSeong Gwan Shin
Seong Gwan Shin
HCHyung Wook Choi
Hyung Wook Choi
CBChung Wung Bark
Chung Wung Bark
Sangmo KimSangmo Kim
Sangmo Kim
Normal perovskite solar cells (PSCs) consist of the following layers: transparent electrode, electron-transport layer (ETL), light-absorbing perovskite layer, hole-transport layer (HTL), and metal electrode. Energy, such as electricity, is produced through light absorbance and electron–hole generation/transport between two electrode types (metal film and transparent conducting film). Among stacked layers in a PSC, the transparent electrode plays the high-performance-power-conversion-efficiency role. Transparent electrodes should have high-visible-range transparency and low resistance. Therefore, in this study, we prepared indium tin oxide (ITO) films on a glass substrate by using facing-target sputtering without substrate heating treatment and investigate the heating-treatment effect on the ITO-film properties for perovskite solar cells (PSCs). Moreover, we fabricated PSCs with ITO films prepared at various oxygen flows during the sputtering process, and their energy-conversion properties are investigated.

28 February 2020 in Japanese Journal of Applied Physics
Verified
Journal Article
Closed access
PDF file
SSSeong Gwan Shin
Seong Gwan Shin
Il Tae KimIl Tae Kim
Il Tae Kim
HCHyung Wook Choi
Hyung Wook Choi
Perovskite has a structure of a large number of solar cells, which is very promising for the rapid commercialization of large-scale, low-cost solar cells. Perovskite solar cells (PSCs) have many advantages, such as their simple processing techniques and inexpensive raw materials. The conduction band of TiO 2 used in many PSCs coincides well with that of the perovskite active layer. In addition, TiO 2 has excellent stability and conductivity and can be obtained by various low-cost deposition methods. However, TiO 2 traps electrons in oxygen vacancies and Ti lattice sites; this leads to recombination, which in turn reduces the efficiency of the device. In this study, we investigated the effects of Fe 3+ and Ga 3+ ions on the efficiency of PSCs by doping them in a compact and mesoporous layer of TiO 2 . As a result, the perovskite solar cell using TiO 2 doped with Fe 3+ and Ga 3+ shows an open-circuit voltage of 0.974 V, current density of 21.909 mA cm −2 , 66.646% fill factor, and 14.21% efficiency. Fe 3+ and Ga 3+ have a smaller atomic radius than Ti 4+ and thus, can replace Ti cations. Furthermore, the Fe 3+ and Ga 3+ doping of TiO 2 is considered to be superior for the photoelectric performance of PSCs.