Dan Liu

Dr. Dan Liu


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 February 2023 in Materials
Verified
Journal Article
Open access
PDF file
GLGuanzhi Li
Guanzhi Li
GSGuibing Shi
Guibing Shi
HMHongyi Miao
Hongyi Miao
DLDan Liu
Dan Liu
ZLZongzhen Li
Zongzhen Li
Li WangLi Wang
Li Wang
FeSiBCuNb powders prepared by the gas atomization method generally exhibit a wide particle size distribution and a high degree of sphericity. In addition, the correspondingly prepared nanocrystalline soft magnetic composites (NSMCs) perform good service stability. In this paper, effects of the gas-atomization pressure and annealing temperature on the microstructure and soft magnetic properties of FeSiBCuNb powders and NSMCs are investigated. The results show that the powders obtained by a higher gas-atomization pressure possess a larger amorphous ratio and a smaller average crystallite size, which contribute to the better soft magnetic performance of the NSMCs. After being annealed at 550 °C for 60 min, the NSMCs show a much better performance than those treated by the stress-relief annealing process under 300 °C, which indicates that the optimization of the soft magnetic properties resulting from the precipitation of the α-Fe(Si) nanocrystalline largely overwhelms the deterioration caused by the grain growth of the pre-existing crystals. In addition, the annealed NSMCs prepared by the powders with the gas-atomization pressure of 4 MPa show the best performance in this work, μe = 33.32 (f = 100 kHz), Hc = 73.08 A/m and Pcv = 33.242 mW/cm3 (f = 100 kHz, Bm = 20 mT, sine wave).

28 October 2022 in Materials
Verified
Journal Article
Open access
PDF file
CZChangshan Zhou
Changshan Zhou
HZHezhi Zhang
Hezhi Zhang
XYXudong Yuan
Xudong Yuan
Kaikai SongKaikai Song
Kaikai Song
DLDan Liu
Dan Liu
Pre-plastic deformation (PPD) treatments on bulk metallic glasses (BMGs) have previously been shown to be helpful in producing multiple shear bands. In this work, the applicability of the PPD approach on BMGs with different Poisson’s ratios was validated based on experimental and simulation observations. It was found that for BMGs with high Poisson’s ratios (HBMGs, e.g., Zr56Co28Al16 and Zr46Cu46Al8), the PPD treatment can easily trigger a pair of large plastic deformation zones consisting of multiple shear bands. These PPD-treated HBMGs clearly display improved strength and compressive plasticity. On the other hand, the mechanical properties of BMGs with low Poisson’s ratios (LBMG, e.g., Fe48Cr15Mo14Y2C15B6) become worse due to a few shear bands and micro-cracks in extremely small plastic deformation zones. Additionally, for the PPD-treated HBMGs with similar high Poisson’s ratios, the Zr56Co28Al16 BMG exhibits much larger plasticity than the Zr46Cu46Al8 BMG. This phenomenon is mainly due to more defective icosahedral clusters in the Zr56Co28Al16 BMG, which can serve as nucleation sites for shear transformation zones (STZs) during subsequent deformation. The present study may provide a basis for understanding the plastic deformation mechanism of BMGs.

30 March 2016 in Metals
Verified
Journal Article
Open access
PDF file
DLDan Liu
Dan Liu
XZXunming Zhu
Xunming Zhu
JQJingyu Qin
Jingyu Qin
AWAimin Wang
Aimin Wang
JDJunpeng Duan
Junpeng Duan
TGTingkun Gu
Tingkun Gu
The structures of a series of Mg–Si liquid alloys were investigated by means of ab initio molecular dynamic simulation. The pair distribution function analysis manifests a tendency of aggregating for the Si–Si pairs in the Mg90Si10 liquid alloy. Chemical short-range orders are observed around Si atoms between unlike atoms, and the maximum is observed for the eutectic Mg47Si53 alloy. Furthermore, the topological environment changed abruptly near the eutectic Mg47Si53 alloy according to Voronoi polyhedra analysis. The variation of diffusion coefficients of Mg and Si suggests that the dynamical properties of Mg–Si liquid alloys are more sensitive to temperature than to compositions.