Division of Electrical, Electronics, and Information Technology, Graduate School of Engineering, Nagasaki Institute of Applied Science, Nagasaki-shi 851-0121, Japan
Prof. Dr. Fujio Kurokawa
Division of Electrical, Electronics, and Information Technology, Graduate School of Engineering, Nagasaki Institute of Applied Science, Nagasaki-shi 851-0121, Japan
This paper presents a fully zero-voltage-switching (ZVS) method and an optimal variable on-time (VOT) control for predictive boundary conduction mode (BCM) boost PFC converter. The operation analysis of BCM boost PFC converter which considers the parasitic capacitances is performed. Based on the analysis, a novel Taylor-approximation method to derive the equations of switching off-time for achieving fully ZVS is proposed. Then, an inductor current approximation method is applied to derive the VOT equation in order to reduce the input current THD. A calculation method for selecting the accurate parasitic capacitances is proposed. Most importantly, the derived equations for achieving ZVS and VOT control are simple and take short calculation time in DSP controller, thus they can be applied to the predictive control. Experimental results demonstrate that the fully ZVS operation can be achieved by the proposed ZVS method. The input current THD is indeed improved by the optimal VOT control.
Due to the increasing demands of safe and efficient renewable energy systems, isolated DC-DC converters became widely used in this field as the essential power conversion blocks. At the same time, such converters are demanded for wide input voltage range and fault tolerance as desirable features. This paper proposes a isolated boost full bridge DC-DC converter which features wide input range and resilient operation along 0 to 100 percent of load current change with a set of active voltage clamping snubber and active start-up circuits. To verify the feasibility of the proposed scheme, the converter is tested experimentally in a 10 kW of output power and the results confirm the effectiveness of the proposed approach.
8 February 2018 in IEEE Transactions on Industrial Electronics
This paper presents an analytical model to design a class-E power amplifier under only zero-voltage-switching (ZVS) term with the MOSFET nonlinear drain-source shunt parasitic capacitance that is named as the subnominal operation. The presented analysis is performed under any grading coefficient m of MOSFET body junction diode and any duty ratio D. The grading coefficient m along with the switching duty ratio D are implemented as tuning variables to satisfy design specifications and ZVS term simultaneously. The restriction of selecting the value of m and D for the subnominal operation has a major effect on simultaneously satisfying of load-resistance, operating frequency, and junction capacitance, which is the main result from this study. The obtained laboratory experiment from the fabricated typical circuit under the required output power 6.2 W with the satisfied duty ratio D = 0.4 is used to show the validity of the theoretical predicted expressions.
4 October 2021 in IEEE Transactions on Aerospace and Electronic Systems
The Japan Aerospace Exploration Agency (JAXA) has developed a power processing unit (PPU) for a 6 kW Hall thruster system. The PPU is a candidate for future mission applications, such as all-electric satellites, exploration vehicles, and orbital transfer services. The PPU has to be small and still provide a wide output range of outputs, consider the in orbit and launch environments, and manage any instability in the Hall thruster's discharge. Specifically, the four converters that make up the anode power supply of the PPU is digitally controlled to reduce the size of the control circuit. It must operate stably despite small output capacitors and long dead times. This paper clarifies the design criteria for the power supply, focusing on the size of capacitors and the PI control parameters to solve these problems. The result is a compact, high-performance PPU for the 6 kW Hall thruster. The power supply meets stringent design criteria and operates the thruster stably with an output voltage that can be varied between 200 and 730 V, provide a maximum power of 5.9 kW, and offer a maximum efficiency of 96.1% in the coupling test for the 6 kW Hall thruster. The proposed PPU, including the anode power supply, achieves a power density of 0.3 kW/kg, significantly higher than that of comparable PPUs.
25 January 2022 in IEEE Transactions on Power Electronics
The purpose of this article is to discuss the design guideline and design chart of the digital peak current mode dc–dc converter using a current–frequency conversion by analyzing its static characteristics. The operation of the proposed method is expressed by equations, and the relationships between controller parameters are derived. This discussion reveals the relationships between the peak current instruction value and the output voltage or peak current, which are necessary for designing the proposed method. Then, the design guideline and design chart are given. The validity of the static characteristic analysis is demonstrated by a prototype, whose design follows the design guideline. An appropriate operation in the steady and static state is also indicated by the experiment. As a result, the validity of the static characteristics and the design guideline of the proposed method can be verified.
This paper presents a novel zero-voltage-switching approach for predictive boundary conduction mode PFC converter for LED lighting. In the proposed method, instead of being detected by a sensing circuit, the switching off-time for achieving zero-voltage-switching is determined by analytical equations of PFC converter. Therefore, the efficiency reduction caused by sensing circuit can be eliminated and the switching losses of MOSFET can be minimized. Experimental results demonstrate that the efficiency is indeed improved.