The paper provides a critical overview of water desalination using geothermal resources. Specific case studies are presented, as well as an assessment of environmental risks and market potential and barriers to growth. The availability and suitability of low and high temperature geothermal energy in comparison to other renewable energy resources for desalination is also discussed. Analysis will show, for example, that the use of geothermal energy for thermal desalination can be justified only in the presence of cheap geothermal reservoirs or in decentralized applications focusing on small-scale water supplies in coastal regions, provided that society is able and willing to pay for desalting.

Field experiments were conducted to determine the effect of water quality (reclaimed and fresh water), water quantity, and their interactions on the growth, yield, and water use efficiency of forage maize during two winter seasons in the Arabian Gulf. The plants irrigated with the reclaimed water had higher plant height than those irrigated with the fresh water. The leaf length and leaf area (cm²) did not show any significant differences among the interaction. Reclaimed water had shorter time for 50% male and female flowering of forage maize plants, indicating earlier maturity. Plants irrigated with reclaimed water had higher chlorophyll content for all levels of water applications. A significant difference in green forage yield was found among the interactions. Reclaimed water gave the highest green forage yield of 72.12 and 59.40 t/ha at 1.4ETo and 1.0ETo, respectively. Plants irrigated with the reclaimed water used water more efficiently [3.65 kg/m³ of DM (dry matter)] than those irrigated with the fresh water [2.91 kg/m³ of DM (dry matter)] for all water quantities. The enhanced growth in wastewater-irrigated crops, compared with fresh water-irrigated crops, was attributed primarily to higher nutrient content (e.g., nitrogen) and lower salinity of the reclaimed water. The study concluded that treated wastewater irrigation increased yields of forage crops and their water use efficiency. Cost-benefit analysis, studies on the use these forage crops as animal feed, and more in depth evaluation of possible crop and soil contamination were recommended.

The potential to improve the tribomechanical performance of HVOF-sprayed WC–12Co coatings was studied by using aqueous WC–12Co suspensions as feedstock. Both as-sprayed and hot-isostatic-pressed (HIPed) coatings were studied. Mathematical models of wear rate based on the structure property relationships, even for the conventionally sprayed WC–Co hardmetal coatings, are at best based on the semiempirical approach. This paper aims to develop these semiempirical mathematical models for suspension sprayed nanocomposite coatings in as-sprayed and heat-treated (HIPed) conditions. Microstructural evaluations included transmission electron microscopy, X-ray diffraction and scanning electron microscopy equipped with energy-dispersive X-ray spectroscopy. The nanohardness and modulus of the coated specimens were investigated using a diamond Berkovich nanoindenter. Sliding wear tests were conducted using a ball-on-flat test rig. Results indicated that the HIPing post-treatment resulted in crystallization of amorphous coating phases and increase in elastic modulus and hardness. Influence of these changes in the wear mechanisms and wear rate is discussed. Results are also compared with conventionally sprayed high-velocity oxy-fuel hardmetal WC–Co coatings.

Photocatalytic TiO₂-PVDF/PMMA nano-composites flat sheet membranes were fabricated by phase inversion and then employed in a crossflow filtration pilot to remove model pollutants of various sizes and charge from aqueous solution. The dope solution contained a mixture of PVDF and PMMA as polymers, polyethylene glycol (PEG) and polyvinylpyrrolidone (PVP) as additives, triethyl phosphate (TEP) as green solvent and TiO₂ as immobilized photo catalyst. After undergoing characterization tests such as SEM morphology thickness, porosity, contact angle and water permeability, the membranes were used to eliminate the model pollutants from synthetic aqueous solution. The impact of the operating conditions (i.e., pH, pressure and initial pollutant concentration) and composition of the doping solution on the performance and photocatalytic and antifouling activity of the membranes was investigated. The results showed that Congo Red and Tartrazine despite their small size were rejected at 99% and 81%, respectively, because of their negative charge, while Ciprofloxacin, which is larger than Tartrazine but of neutral charge, crossed the membrane. The permeability did not decrease with a decline in pollutant concentration but diminished when the pressure increased and was reduced by more than half for wastewater.

Corrosion properties of nanostructured coatings deposited by suspension high-velocity oxy-fuel (S-HVOF) via an aqueous suspension of milled WC-Co powder were compared with conventional HVOF-sprayed coatings. Microstructural evaluations of these coatings included x-ray diffraction and scanning electron microscopy equipped with an energy-dispersive x-ray spectroscopy. The corrosion performance of AISI440C stainless steel substrate and the coatings was evaluated in a 3.5 wt.% NaCl aqueous solution at ~ 25 °C. The electrochemical properties of the samples were assessed experimentally, employing potentiodynamic polarization and electrochemical impedance spectroscopy. The potentiodynamic polarization results indicated that coatings produced by S-HVOF technique show lower corrosion resistance compared with the coatings produced by HVOF-JK (HVOF Jet Kote) and HVOF-JP (HVOF JP5000) techniques. Results are discussed in terms of corrosion mechanism, Bode and Nyquist plots, as well as equivalent circuit models of the coating–substrate system.