Yeon-Ho Oh

Dr. Yeon-Ho Oh

korea electrotechnology research institute
orcid

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 December 2020 in Energies
Verified
Journal Article
Open access
PDF file
WLWoo-Young Lee
Woo-Young Lee
JJJang-Un Jun
Jang-Un Jun
HOHo-Seok Oh
Ho-Seok Oh
JUNKYU PARKJUNKYU PARK
JUNKYU PARK
YOYeon-Ho Oh
Yeon-Ho Oh
HJHyun-Jae JANG
Hyun-Jae JANG
In the study, an interrupting performance test on the 145 kV gas circuit breaker is performed according to three different gases: SF6, g3 (5% NovecTM4710 with 95% CO2), and CO2(70%)/O2(30%) gases. Thanks to research advancements, it is confirmed that CO2 and g3 (5% NovecTM 4710) gases, respectively, have 40% and 75% dielectric strength, compared to that of SF6 gas. The filling pressure and transient recovery voltage criteria of each gas were determined differently in order to compare the maximum interrupting performance of each gas. The pressure of SF6 gas was determined to be 5.5 bar, which is typically used in circuit breakers. The pressure of the other two gases was determined to be 8.0 bar (the maximum available pressure of the test circuit breaker) to find the maximum interrupting performance. Moreover, the rate-of-rise of transient recovery voltage of SF6 was determined as 10 kV/μs, which is the value at the state of maximum interrupting performance of the test circuit breaker with SF6. On the other hand, the rate-of-rise of transient recovery voltages of g3 (5% NovecTM4710 with 95% CO2) and CO2(70%)/O2(30%) gases were, respectively, determined as 4∼5 kV/μs to find the interruption available point. The characteristics of arc conductance, arc current, and arc voltage near the current zero, and post-arc current are analyzed to compare the interrupting performance, according to different arc-quenching gases. The arc current is measured using a current transformer (Rogowski coil), and a signal processing method of the arc current and arc voltage is introduced to increase the reliability of the interrupting performance results. As a result of the test, it is confirmed that the critical arc conductance for all test conditions converged within a certain range and the value is around 0.7 mS. In addition, the critical current slope just before the current zero-crossing during the interrupting process is shown to be 1.8 A/μs between interruption success and failure. Consequently, it is verified that the CO2(70%)/O2(30%) mixture and g3 (5% NovecTM4710 with 95% CO2) have a similar arc extinguishing performance and SF6 has a relatively higher extinguishing performance than that of CO2(70%)/O2(30%) mixture and g3 (5% NovecTM4710 with 95% CO2) under the aforementioned filling pressure and TRV conditions.

15 May 2023 in Computational and Theoretical Chemistry
Verified
Journal Article
Open access
NSNidhi Sinha
Nidhi Sinha
HCHeechol Choi
Heechol Choi
MSMi-Young Song
Mi-Young Song
HJHyun-Jae Jang
Hyun-Jae Jang
YOYeon-Ho Oh
Yeon-Ho Oh
KSKi-Dong Song
Ki-Dong Song

23 November 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
NSNidhi Sinha
Nidhi Sinha
MSMi-Young Song
Mi-Young Song
HCHyonu Chang
Hyonu Chang
HCHeechol Choi
Heechol Choi
HJHyun-Jae JANG
Hyun-Jae JANG
KSKi-Dong Song
Ki-Dong Song
Electron impact scattering from C3F6O is studied in this work. The R-matrix method was used for the calculations of elastic, momentum transfer, and excitation cross sections. The attachment cross section was obtained through a parametric estimator based on the R-matrix outputs. The Binary-Encounter-Bethe (BEB) method was used for computing the ionization cross section. The obtained cross section set was used for the transport studies using the BOLSIG+ code, which is a two-term Boltzmann equation solver. The present calculation was performed for steady-state Townsend experimental conditions for E/N, covering a range of 100–1000 Td. The critical dielectric strength of pure C3F6O was found to be 475 Td, which is much greater than that of SF6 (355 Td). The effect of the addition of different buffer gases, such as CO2, N2, and O2, was also examined. For the C3F6O–CO2, C3F6O–N2, and C3F6O–O2 mixtures with 65%, 55%, and 60% C3F6O, respectively, the critical dielectric strength was determined to be essentially the same as that of pure SF6. The presence of synergism was confirmed for these gas mixtures. We further derived the Paschen curve using a fitting method with the transport parameters as the basic inputs. The minimum breakdown voltage of C3F6O accounted for only 55% of that of SF6. The buffer gas mixture improved the condition; however, the performance of CO2 and O2 mixtures was not satisfactory. The addition of N2 as the buffer gas significantly improved the breakdown property of the gas. The mixture of ≥99% of N2 or ≤1% of C3F6O gave a better breakdown characteristic than SF6. Any proportion ≥90% of N2 or ≤10% of C3F6O was suitable in the higher pressure ranges. The present work demonstrates the potential of C3F6O as a substitute gas for SF6 with a negligible environmental threat.

25 November 2024 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
HAHyun-Mo Ahn
Hyun-Mo Ahn
JUNKYU PARKJUNKYU PARK
JUNKYU PARK
HJHyun-Jae Jang
Hyun-Jae Jang
YOYeon-Ho Oh
Yeon-Ho Oh
SHSung-Chin Hahn
Sung-Chin Hahn
KSKi-Dong Song
Ki-Dong Song
This study presents an efficient hybrid mechanical and power electronic (MPE) DC circuit breaker (DCCB) to solve the challenges of conventional hybrid MPE DCCBs. The main branch of the proposed topology reduces on-state losses to a negligible magnitude by utilizing only mechanical switches such as the residual current switch (RCS), fast mechanical switch (FMS), and monostable mechanical switch (MMS). Additionally, it significantly decreases the number of semiconductor devices by employing a series connection between the FMS and the main current breaker (MCB). The DC interruption capability of the proposed hybrid MPE DCCB topology was verified through a simulation based on equivalent electric circuits, and the DC interruption capability of the proposed medium-voltage (MV) class hybrid MPE DCCB was evaluated using a DC interruption test.

30 March 2018 in IEEE Transactions on Plasma Science
Verified
Journal Article
Closed access
YOYeon-Ho Oh
Yeon-Ho Oh
HLHae June Lee
Hae June Lee
KSKi-Dong Song
Ki-Dong Song
JKJin-Ki Kim
Jin-Ki Kim
SHSung-Chin Hahn
Sung-Chin Hahn
This paper represents the prediction of the thermal interruption characteristics of a 72.5-kV CO 2 circuit breaker (CB). An analysis method to simulate CO 2 arc plasma was developed. The principle phenomena of CO 2 arc plasma-nonideal gas behavior, radiative heat transfer (RHT), and nozzle ablation-were considered. In addition, the electric field analysis to compute ohmic heating in the arc region and the analysis of turbulent flows were conducted. The absorption coefficients used in RHT were simplified into mean values of 10 frequency bands to represent the entire absorption spectrum. The proposed method was verified through experimental tests of pressure rise and arc voltage. To predict the thermal interruption characteristics, post arc current (PAC) was computed. PAC is the minute current existing between the contacts of a CB after current zero, and has important value to comprehensively understanding thermal interruption. For comparison, a 72.5-kV CO 2 CB was manufactured and tested, and the results were compared with the results of the thermal interruption tests.

1 April 2020 in AIP Advances
Verified
Journal Article
Open access
PDF file
HJHyun-Jae JANG
Hyun-Jae JANG
YOYeon-Ho Oh
Yeon-Ho Oh
KSKi-Dong Song
Ki-Dong Song
YKYoung-Il Kim
Young-Il Kim
The dielectric breakdown properties of dry air, which is widely used as the insulation gas in switchgears of electric distribution systems, are determined for dry-air switchgear analysis and design. In this study, a two-term Boltzmann analysis was applied to investigate the dielectric breakdown properties of dry air with increasing temperatures (300–5000 K) at atmospheric pressure (0.1 MPa). According to the changes in the component ratios of dry air, the collision cross sections of high-mole-fraction decomposition species were considered. In order to analyze the contribution of each dry-air decomposition species to dielectric properties, we compared the dielectric properties calculated with and without considering small amounts of the species, such as Ar and CO2, in actual dry air. The results show that reliable calculations can be obtained for dry air at atmospheric pressure and temperatures up to 5000 K only by considering species with mole fractions exceeding 10−2 in the composition. Based on the calculations, it is observed that the reduced critical dielectric strength of dry air does not significantly change for temperatures up to 2000 K. This means that the dielectric properties of dry air show temperature independence over a wider temperature range than those of SF6.