In this article, the subthreshold characteristics of a tunable single input CMOS Schmitt trigger (ST) are modeled for the first time. The high-to-low and low-to-high hysteresis transition points are analytically determined as a function of the tuning voltages and the transistors’ geometrical parameters. The derived expressions allow to design the ST with desired hysteresis width in subthreshold region. Furthermore, the proposed model allows to estimate the minimum supply voltage for which hysteresis occurs. The derived expressions also provide physical insight into the circuit behavior, by predicting the effect of supply voltage and temperature variations on the hysteresis width. The model is validated through simulations, and the maximum error between the analytical and simulated transition points is less than 5%. The model is also experimentally validated with an ASIC fabricated in AMS 0.35µm CMOS process. The maximum error between the analytical and measured transition points is below 6%. The analytical model allows performance optimization in subthreshold region for low power applications.

Silicon-based kinetic energy converters employing variable capacitors, also known as electrostatic vibration energy harvesters, hold promise as power sources for Internet of Things devices. However, for most wireless applications, such as wearable technology or environmental and structural monitoring, the ambient vibration is often at relatively low frequencies (1–100 Hz). Since the power output of electrostatic harvesters is positively correlated to the frequency of capacitance oscillation, typical electrostatic energy harvesters, designed to match the natural frequency of ambient vibrations, do not produce sufficient power output. Moreover, energy conversion is limited to a narrow range of input frequencies. To address these shortcomings, an impacted-based electrostatic energy harvester is explored experimentally. The impact refers to electrode collision and it triggers frequency upconversion, namely a secondary high-frequency free oscillation of the electrodes overlapping with primary device oscillation tuned to input vibration frequency. The main purpose of high-frequency oscillation is to enable additional energy conversion cycles since this will increase the energy output. The devices investigated were fabricated using a commercial microfabrication foundry process and were experimentally studied. These devices exhibit non-uniform cross-section electrodes and a springless mass. The non-uniform width electrodes were used to prevent pull-in following electrode collision. Springless masses from different materials and sizes, such as 0.5 mm diameter Tungsten carbide, 0.8 mm diameter Tungsten carbide, zirconium dioxide, and silicon nitride, were added in an attempt to force collisions over a range of applied frequencies that would not otherwise result in collisions. The results show that the system operates over a relatively wide frequency range (up to 700 Hz frequency range), with the lower limit far below the natural frequency of the device. The addition of the springless mass successfully increased the device bandwidth. For example, at a low peak-to-peak vibration acceleration of 0.5 g (peak-to-peak), the addition of a zirconium dioxide ball doubled the device’s bandwidth. Testing with different balls indicates that the different sizes and material properties have different effects on the device’s performance, altering its mechanical and electrical damping.

Inductive and capacitive impedance matching are two different techniques optimizing power transfer in magnetic resonance inductive wireless power transfer. Under ideal conditions, i.e., unrestricted parameter ranges and no loss, both approaches can provide the perfect match. Comparing these two techniques under non-ideal conditions, to explore fundamental differences in their performance, is a challenging task as the two techniques are fundamentally different in operation. In this paper, we accomplish such a comparison by determining matchable impedances achievable by these networks and visualizing them as regions of a Smith chart. The analysis is performed over realistic constraints on parameters of three different application cases both with and without loss accounted for. While the analysis confirms that it is possible to achieve unit power transfer efficiency with both approaches in the lossless case, we find that the impedance regions where this is possible, as visualized in the Smith chart, differ between the two approaches and between the applications. Furthermore, an analysis of the lossy case shows that the degradation of the power transfer efficiencies upon introduction of parasitic losses is similar for the two methods.

This article reports two low power wake-up receiver (WuRx) circuits (Type A and B) for underwater acoustic wireless sensor networks. The proposed circuits realize the same novel method to extract the wake-up call from the acoustic signals received by a sensor node using different circuit topologies. This is accomplished by comparing the amplitude and the duration of the received pulses to a predefined code. A combination of these two parameters provides a safe and robust decoding system. The values and duration of the predefined code can be adjusted by tuning the biasing voltages in the circuits. The main advantages of the presented designs are modularity and tunability. To verify the operation of the proposed system, an ASIC has been realized. The WuRxs have been characterized in terms of tuning, duty cycle, and power consumption. Both WuRxs can consume less than 0.5 $\mu \text{W}$ . Type A occupies an area of 0.058 mm2, has a data rate of 250 bit/s, and presents the lowest power consumption reported, consuming 265 nW and 61 nW in active and sleep modes, respectively.

This paper presents a single-sided impedance matching technique, i.e., matching from only the transmitter or receiver side, using a switchable interspiraled coil. This technique is suited for active impedance matching in magnetic resonance wireless power transfer. The switchable coil consists of 9 selectable, single-turn coils placed in-between the 9.5 turns of a spiraled resonator coil with an inductance of approximately 8 $\mu H$ . The self-inductances of the single-turn coils vary between 33-493 $nH$ . The interspiraled coil was realized on a single-sided PCB, making the system compact in size. Circuit analysis and simulation show that the inductance selectability enables impedance matching over a range of distances in a Wireless Power Transfer (WPT) System at 6.78 MHz operation frequency. Measurement and simulation of the efficiency indicate that the proposed interspiraled coil may significantly improve the Power Transfer Efficiency (PTE) when the distance and the load change.

Carbon nanotubes (CNTs) can be grown locally on custom-designed CMOS microstructures to use them as a sensing material for manufacturing low-cost gas sensors, where CMOS readout circuits are directly integrated. Such a local CNT synthesis process using thermal chemical vapor deposition (CVD) requires temperatures near 900 °C, which is destructive for CMOS circuits. Therefore, it is necessary to ensure a high thermal gradient around the CNT growth structures to maintain CMOS-compatible temperature (below 300 °C) on the bulk part of the chip, where readout circuits are placed. This paper presents several promising designs of CNT growth microstructures and their thermomechanical analyses (by ANSYS Multiphysics software) to check the feasibility of local CNT synthesis in CMOS. Standard CMOS processes have several conductive interconnecting metal and polysilicon layers, both being suitable to serve as microheaters for local resistive heating to achieve the CNT growth temperature. Most of these microheaters need to be partially or fully suspended to produce the required thermal isolation for CMOS compatibility. Necessary CMOS post-processing steps to realize CNT growth structures are discussed. Layout designs of the microstructures, along with some of the microstructures fabricated in a standard AMS 350 nm CMOS process, are also presented in this paper.