A normally-off GaN double-implanted vertical MOSFET (DMOSFET) with an atomic layer deposition (ALD)-Al2O3 gate dielectric film on a free-standing GaN substrate fabricated by triple ion implantation is presented. The DMOSFET was formed with Si ion implanted source regions in a Mg ion implanted p-type base with N ion implanted termination regions. A maximum drain current of 115 mA/mm, maximum transconductance of 19 mS/mm at a drain voltage of 15 V, and a threshold voltage of 3.6 V were obtained for the fabricated DMOSFET with a gate length of 0.4 μm with an estimated p-type base Mg surface concentration of 5 × 1018 cm−3. The difference between calculated and measured Vths could be due to the activation ratio of ion-implanted Mg as well as Fermi level pinning and the interface state density. On-resistance of 9.3 mΩ·cm2 estimated from the linear region was also attained. Blocking voltage at off-state was 213 V. The fully ion implanted GaN DMOSFET is a promising candidate for future high-voltage and high-power applications.
Vertical structured Gallium nitride (GaN) p-n junction diodes with improved breakdown properties have been demonstrated using high-k dielectric passivation underneath the field plate. Simulation results at a reverse voltage of 1 kV showed that the maximum electric field near the mesa-etched p-n junction edges covered with film of dielectric constant k = 10 was reduced to 2.0 MV/cm from 3.0 MV/cm (SiO2 (k = 3.9)). The diodes were fabricated using the high-k mixed oxide of SiO2 and CeO2 with k = 12.3. I–V characteristics of the diode with a field plate showed a breakdown voltage above 2 kV with an increased avalanche resistance. This means that the electric field reduces at the periphery of the mesa-etched p-n junction and is uniformly formed across the whole p-n junction. It is clear that high-k dielectric film passivation and filed plate termination are essential techniques for GaN power devices.
1 June 2019 in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
In this paper, we propose a novel delta-sigma modulator (DSM) that reduces the effects of clock jitter and excess loop delay by using a vector filter in the feedback path. The vector filter divides the input signal into a high-frequency part and a low-frequency part. The low-pass signal is placed in the path to the first-stage digital-to-analog converter for reducing the effects of the clock jitter, and the high-pass signal is placed in the feedback path to the last integrator in order to compensate for the excess loop delay. The DSM using the vector filter in the feedback path (DSM-VF) is verified using MATLAB/Simulink. Further, a clock jitter (0.1 %) in DSM-VF leads to an improvement in the signal-to-noise-ratio (SNR) to 22.5 dB as compared to the SNR of a conventional CTDSM. Moreover, the SNR deterioration caused by the excess loop delay is improved.
Mg-ion-implanted layers in a GaN substrate after annealing were investigated. Implanted Mg atoms precipitated along the edges of crystal defects were observed using 3D-APT. The breakdown characteristics of a GaN double-diffused vertical MISFET (DMISFET) fabricated via triple ion implantation are presented. A DMISFET with Si-ion-implanted source regions was formed in Mg-ion-implanted p-base regions, which were isolated from adjacent devices by N-ion-implanted edge termination regions. A threshold voltage of −0.5 V was obtained at a drain voltage of 0.5 V for the fabricated vertical MISFET with an estimated Mg surface concentration of 5 × 1018 cm−3. The maximum drain current and maximum transconductance in a saturation region of Vds = 100 V were 2.8 mA/mm and 0.5 mS/mm at a gate voltage of 15 V, respectively. The breakdown voltage in the off-state was 417 V. The breakdown points were determined by the boundary regions between the N- and Mg-implanted regions. By improving heat annealing methods, ion-implanted GaN DMISFETs can be a promising candidate for future high-voltage and high-power applications.
11 July 2015 in Analog Integrated Circuits and Signal Processing