Vertical structure GaN power devices fabricated on freestanding GaN substrates have high potentials in ideally efficient energy conversion systems. This letter describes successful acquisition of high avalanche capabilities for high breakdown voltage GaN p-n junction diodes. We have already reported the high avalanche capability by applying a punch-through structure in p-GaN layer, however; the structure caused a drawback of increase in on-resistance and turn-on voltage. By applying a newly developed two-step mesa structure consisting of the first inner mesa with partially thinned p-GaN layer and the second outer mesa etched to n-GaN drift layer, the high avalanche capabilities with reversible current-voltage characteristics have been realized at high breakdown voltages of 4.7-4.8 kV without sacrificing the forward I-V characteristics. The two-step mesa structure transferred the position of the peak electric field in the p-n junction from the dry-etch damaged second outer mesa to the first mesa covered by the thinned p-GaN layer, which could lead the mild breakdown. The high avalanche capability was obtained with good reproducibility regardless of the anode electrode diameter. This structure can contribute to the construction of robust power systems.
16 April 2019 in Japanese Journal of Applied Physics
In order to avoid sudden catastrophic hard breakdown in high breakdown voltage vertical GaN p–n junction diodes, punch-through induced breakdown structures have been newly considered. Mg acceptor concentration in the p-GaN layer was reduced so that the punch-through breakdown occurred before the hard breakdown. By using a wafer with triple drift layers and the p-GaN layer with lowered Mg concentration of 3 × 10 17 cm −3 grown on a freestanding n-GaN substrate, the diode showed a high breakdown voltage of 4.9 kV with high reverse avalanche capabilities against sudden increase of reverse current over 5 orders of magnitudes. No degradation was observed after fifteen repetitive measurements.
A simple setup for electrodeless photo–assisted electrochemical (PEC) etching was discussed from the viewpoint of the experimental geometry, in which the sample was dipped into the electrolyte under ultraviolet (UV) irradiation. Sulfate radicals (SO4•–) were produced from K2S2O8 with UV light as the oxidizing agent; this consumed the extra UV photogenerated electrons, making it electrodeless. The transmittances were measured for various concentrations of K2S2O8 (aq.) to adjust the electrolyte depth. The effect of tetramethylammonium hydroxide post-treatment was also examined. The results indicate that damage-free PEC etching is feasible for everyone, even those who are not familiar with electrochemistry.
Low dislocation density and low-resistance GaN wafers are in high demand for improving the performance of vertical GaN power devices. Recently, GaN wafers with the dislocation density of 8.8 × 104 cm−2 and the resistivity of 7.8 × 10−4 Ω cm, were fabricated using oxide vapor phase epitaxy (OVPE). In this study, GaN p–n diodes on GaN wafers prepared by the OVPE method were evaluated for verifying their suitability as vertical GaN power devices. An extremely low-differential specific on-resistance of 0.08 mΩ cm2 and a high breakdown voltage of 1.8 kV were obtained from forward and reverse I–V measurements.
Vertical structured Gallium nitride (GaN) p-n junction diodes with improved breakdown properties have been demonstrated using high-k dielectric passivation underneath the field plate. Simulation results at a reverse voltage of 1 kV showed that the maximum electric field near the mesa-etched p-n junction edges covered with film of dielectric constant k = 10 was reduced to 2.0 MV/cm from 3.0 MV/cm (SiO2 (k = 3.9)). The diodes were fabricated using the high-k mixed oxide of SiO2 and CeO2 with k = 12.3. I–V characteristics of the diode with a field plate showed a breakdown voltage above 2 kV with an increased avalanche resistance. This means that the electric field reduces at the periphery of the mesa-etched p-n junction and is uniformly formed across the whole p-n junction. It is clear that high-k dielectric film passivation and filed plate termination are essential techniques for GaN power devices.
16 April 2019 in Japanese Journal of Applied Physics
Pulsed photo-electrochemical (PEC) etching was performed to fabricate mesa-structure vertical GaN p–n junction diodes without process damages which are inevitable in the conventional dry etching process. The damage-free etched surface was confirmed by photoluminescence and cathode luminescence measurements. The most beneficial property of the GaN p–n junction diodes fabricated by PEC etching was the much reduced variation in their breakdown voltages (3.83–3.88 kV) compared with those fabricated by conventional dry etching (3.36–3.81 kV). These results indicate the excellent potential of PEC etching in the fabrication of GaN power devices.