Direct ink writing (DIW)-based 3D printing process has gained significant attention due to its ability to accommodate versatile ink materials. However, the most challenging aspect of DIW is the development of inks with suitable printability. To address this, we demonstrate a numerical approach using the finite element method (FEM) to model the printability of inks. Five distinct ink models, including cement, thermoset polymer (epoxy), biopolymer (cellulose nanocrystals), and two hydrogel inks (alginate-based biopolymer and metallic powder), have been chosen to identify the key differentiating characteristics between inks with high and low printability. We focus on the shear thinning behavior, shape retention, and ink blockage region as key factors to evaluate printability and propose a printability grading parameter that demonstrates the qualitative ranking of inks based on their rheology. The study reveals that inks with better printability exhibit greater shear thinning behavior, yield shear strength, shape retention, and viscosity at a suitable inlet pressure. Among all the inks studied, we have found a specific concentration of cellulose nanocrystals (20 wt%) that demonstrates the best printability.
In recent years, solar thermal energy (STE) has attracted energy researchers because of its higher efficacy compared to the photovoltaic solar cell. STE is one of the forms of solar energy whereby heat is transferred via a secondary medium called heat transfer fluids (HTFs). Therefore, the overall performance of STE depends on the thermophysical properties and thermal performance of the HTFs. Traditional HTFs suffer from low decomposition temperature, high melting point, and higher vapor pressure. To overcome these limitations, researchers have recently begun working on new HTFs for STE. Ionic liquids (ILs) are considered as a potential candidate for the next generation of HTFs because of their enhanced thermophysical properties, such as thermal stability at high temperature, insignificant vapor pressure, and high ionic conductivity. In addition, thermophysical properties and thermal performance of ILs can be further enhanced by dispersing nanoparticles, which is one of the emerging research interests to improve the efficiency of the solar thermal system. This paper summarizes the recent study of ILs-based nanofluids as HTFs. These summaries are divided into two sections (i) thermophysical properties studies, such as density, viscosity, thermal conductivity, and heat capacity, and (ii) thermal performance studies such as natural convection and forced convection. Synthesis of ILs-based nanofluids and thermophysical properties measurement techniques are also discussed. Based on these state-of-the-art summaries, we offer recommendations for potential future research direction for ILs-based nanofluids.
This study investigates the enhancement of the rate of evaporation from a nanoengineered solid surface using non-equilibrium molecular dynamics simulation. Four different types of surface modifications were introduced to examine the thermal transportation behavior. The surface modification includes: (1) transformation of surface wetting condition from hydrophobic to hydrophilic, (2) implementing nanostructures on the smooth surface, (3) cutting nano slots on the smooth surface and (4) introducing nano-level surface roughness. Evaporation behavior from the same effective surface area was also studied. The simulation domain consisted of three distinct zones: solid base wall made of copper, a few layers of liquid argon, and a vapor zone made of argon. All the nano-level surface modifications were introduced on the solid base surface. The few layers of liquid argon representing the liquid zone of the domain take heat from the solid surface and get evaporated. Outside this solid and liquid zone, there is argon vapor. The simulation began at the initial time t = 0 ns and then was allowed to reach equilibrium. Immediately after equilibrium was achieved on all three-phase systems, the temperature of the solid wall was raised to a higher value. In this way, thermal transportation from the solid wall to liquid argon was established. As the temperature of the solid wall was high enough, the liquid argon tended to evaporate. From the simulation results, it is observed that during the transformation from hydrophobic to hydrophilic conditions, enhancement of evaporation takes place due to the improvement of thermal transportation behavior. At the nanostructure surface, the active nucleation sites and effective surface area increase which results in evaporation enhancement. With nano slots and nano-level surface roughness, the rate of evaporation increases due to the increase of solid-liquid contact area and effective surface area.
10 August 2023 in ASME Journal of Heat and Mass Transfer
In this paper, a novel sinusoidal wavy mini-channel heat sink (MCHS) with inter-connectors (IC w-MCHS) has been introduced, and the effectiveness of the proposed heat sink over conventional mini-channel heat sink (s-MCHS) has been numerically investigated. Different parameters, i.e., wavelengths, wave amplitudes, and phase shifts of the proposed sinusoidal wavy MCHS, were varied to study its effect on thermal and hydraulic performance. This study used three different wavelengths, three different amplitudes, and two different phase shifts, and Reynolds number (Re) varied from 300 to 800. The Nusselt number (Nu) of IC w-MCHS increased as the wave amplitude ratio (α) and Re increased, whereas it increased with the decrement of the wavelength ratio (β). Nu of the IC w-MCHS was also found to depend on phase shift (θp); for θp = π, the chaotic advection and increment of flow reversal were observed in the IC w-MCHS compared to θp = 0, resulting in higher Nu and higher pressure drop penalty. Nu of the IC w-MCHS was found to be 115% higher compared to s-MCHS at Re 550, θp = π,and a = 0.3,whereas it was found 77% higher for θp = 0. The maximum temperature of the IC w-MCHS heat sink was also found to decrease compared to that of the s-MCHS due to enhanced coolant mixing. A maximum26% decrease in the heat sink temperature was observed for the IC w-MCHS at Re 800 compared to the s-MCHS.