In recent years, solar thermal energy (STE) has attracted energy researchers because of its higher efficacy compared to the photovoltaic solar cell. STE is one of the forms of solar energy whereby heat is transferred via a secondary medium called heat transfer fluids (HTFs). Therefore, the overall performance of STE depends on the thermophysical properties and thermal performance of the HTFs. Traditional HTFs suffer from low decomposition temperature, high melting point, and higher vapor pressure. To overcome these limitations, researchers have recently begun working on new HTFs for STE. Ionic liquids (ILs) are considered as a potential candidate for the next generation of HTFs because of their enhanced thermophysical properties, such as thermal stability at high temperature, insignificant vapor pressure, and high ionic conductivity. In addition, thermophysical properties and thermal performance of ILs can be further enhanced by dispersing nanoparticles, which is one of the emerging research interests to improve the efficiency of the solar thermal system. This paper summarizes the recent study of ILs-based nanofluids as HTFs. These summaries are divided into two sections (i) thermophysical properties studies, such as density, viscosity, thermal conductivity, and heat capacity, and (ii) thermal performance studies such as natural convection and forced convection. Synthesis of ILs-based nanofluids and thermophysical properties measurement techniques are also discussed. Based on these state-of-the-art summaries, we offer recommendations for potential future research direction for ILs-based nanofluids.
22 February 2013 in Journal of Thermal Science and Engineering Applications
The present work experimentally investigates the effect of synthetic jets on the heat transfer performance in a microchannel heat sink. The heat sink consists of five parallel rectangular microchannels measuring 500 μm wide, 500 μm deep, and 26 mm long each. An array of synthetic jets with 100 μm diameter orifices is placed right above the microchannel with a total of eight jet orifices per channel. Microjets are synthesized from the fluid flowing through the microchannel. Periodic disturbances are generated when the synthetic jets interact with the microchannel flow. Heat transfer performance is enhanced as local turbulence is generated and penetrates the thermal boundary layer near heated channel wall. The effects of synthetic jets on microchannels heat transfer performance are studied for several parameters including the channel stream flow rate, the synthetic jets strength and operating frequency. It shows that the synthetic jets have higher heat transfer enhancement for microchannel flow at lower channel flow rates. A maximum of 130% heat transfer enhancement is achieved for some test cases. The pressure dynamics introduced by the synthetic jets are also investigated. The synthetic jets cause a minor increase in the pressure drop.
15 July 2019 in Journal of Thermal Science and Engineering Applications
In this paper, experimental investigation has been performed to characterize the heat transfer behavior of CuO–water and ZnO–water nanofluids. Nanofluids containing different volume percent (vol %) of nanoparticle concentrations flowed over a flat copper plate under a constant heat load. The constant heat flux was maintained using evenly placed cartridge heaters. The heat transfer coefficients of nanofluids were measured and compared with the results obtained from identical experiments performed with de-ionized (DI) water. In order to thoroughly characterize the nanofluids, nanoparticle size was investigated to inspect for possible agglomeration. The particle size was measured by using both a transmission electron microscope (TEM) and a dynamic light scattering system (DLS). Enhancement of convective heat transfer of nanofluids was 2.5–16% depending on the nanoparticle concentrations and Reynolds number. The plausible mechanisms of the enhanced thermal performance of CuO and ZnO nanofluids will be discussed in the following paper.
A global model is proposed to simulate the drying process of used nuclear fuel assemblies under vacuum drying conditions. The transient model consists of a coupled mass and energy conservation equation with appropriate source and sink terms. The classic Hertz-Knudsen expression is employed to resolve the evaporation rate and the associated water mass depletion in the system. Both latent heat of vaporization and residual decay heat are considered as sink and source in the energy conservation, respectively. The model is employed to simulate vacuum drying of spent nuclear fuel rod storage systems. Multistage stepwise vacuuming of the system is emulated, and several parametric studies are conducted to identify their role in the drying process. The predicted temporal profiles show that the proposed model is able to capture qualitative trends of the water removal rate, hence the dryness level of the system. The model prediction is also compared against experiments where the amount of residual water after a standard vacuum drying procedure is quantified. The predictions are found to compare favorably with the experimental measurements.
28 January 2019 in Journal of Inorganic and Organometallic Polymers and Materials