The influence of random surface roughness of Au films on the Casimir force is explored with atomic force microscopy in the plate-sphere geometry. The experimental results are compared to theoretical predictions for separations ranging between 20 and . The optical response and roughness of the Au films were measured and used as input in theoretical predictions. It is found that at separations below , the roughness effect is manifested through a strong deviation from the normal scaling of the force with separation distance. Moreover, deviations from theoretical predictions based on perturbation theory can be larger than 100%.
Capillary forces have been measured by atomic force microscopy in the plate-sphere setup between gold, borosilicate glass, GeSbTe, titanium, and UV-irradiated amorphous titanium-dioxide surfaces. The force measurements were performed as a function contact time and surface roughness in the range rms and relative humidity ranging between 2% and 40%. It is found that even for the lowest attainable relative humidity very large capillary forces are still present. The latter suggests the persistence of a nanometers-thick adsorbed water layer that acts as a capillary bridge between contacting surfaces. Moreover, we found a significantly different scaling behavior of the force with rms roughness for materials with different hydrophilicity as compared to gold-gold surfaces.
In this work we explore the influence of self-affine roughness on the pull-in parameters for switches used in micro/nanoelectromechanical devices in the presence of the Casimir force. The pull-in parameters are described, respectively, by the ratios of the Casimir and electrostatic forces with respect to that of an elastic restoring force. It is shown that the roughness exponent , which for self-affine roughness characterizes the degree of surface irregularity at short length scales, has significant influence on the Casimir force and consequently on the pull-in parameters. Indeed, significant changes of the ratio of the Casimir to restoring force take place for roughness exponents , while larger exponents have an effect that saturates rather fast especially for values close to that of a smooth hill-valley topography . For the ratio of the electrostatic to restoring force, the influence of the roughness exponent is less prominent for relatively large normalized plate separations (with respect to the initial separation in the absence of any forces). In any case, the largest influence of the roughness exponent on the ratio of the Casimir to restoring force takes place for relatively weak electrostatic forces.
Amorphous to crystalline phase transitions in phase change materials (PCM) can have strong influence on the actuation of microelectromechanical systems under the influence of Casimir forces. Indeed, the bifurcation curves of the stationary equilibrium points and the corresponding phase portraits of the actuation dynamics between gold and AIST (Ag${}_{5}$In${}_{5}$Sb${}_{60}$Te${}_{30}$) PCM, where an increase of the Casimir force of up $\sim${}25$%$ has been measured upon crystallization, show strong sensitivity to changes of the Casimir force as the stiffness of the actuating component decreases and/or the effective interaction area of the Casimir force increases, which can also lead to stiction. However, introduction of intrinsic energy dissipation (associated with a finite quality factor of the actuating system) can prevent stiction by driving the system to attenuated motion towards stable equilibrium depending on the PCM state and the system quality factor.
Here, we investigated the static and the dynamic wetting behaviors of copper (Cu) thin films deposited by DC magnetron sputtering. The deposited films have random rough surfaces for which the rms roughness amplitude , the lateral correlation length , and the roughness exponent were obtained from the analysis of height topography images acquired by atomic force microscopy. The time-dependent height-height correlation functions indicated anomalous kinetic roughening with roughness exponents α ≈ 0.9 and evolving roughness parameters and with deposition time. The latter yields a nonstationary local surface slope that has a crucial impact on the surface wettability. Indeed, static and dynamic contact angles’ (CAs) measurements revealed two wetting regimes associated with different growth stages leading to a transition from a metastable Cassie-Baxter to a Wenzel-like state for the roughest films. Moreover, the increasing roughness with well distributed peaks and valleys leads to increasing CAs due to trapped air in surface cavities, while after some point the larger surface features lead to a decrement of the CAs that vary only slightly with further roughening. Although the apparent wetting transition with increasing surface roughness is not favored by the local Laplace pressure estimation, the energy of the system decreases with surface roughening, or equivalently increasing local surface slope, favoring energetically a Wenzel state. Under these conditions, the water droplet can spontaneously fill the surface cavities once the impregnation is initiated by the hydrophilic nature of the surface, in agreement with our experiments for significantly large local surface slopes ρ (>0.1) and large roughness exponents α ∼ 1.