Methods to achieve large-scale production of defect-free graphene are needed to enable the commercial development of graphene-based devices. It is now shown that high-shear mixing is an effective way to exfoliate graphene and other two-dimensional materials in liquid volumes up to hundreds of litres.
Few-layer black phosphorus (BP) is a new two-dimensional material which is of great interest for applications, mainly in electronics. However, its lack of environmental stability severely limits its synthesis and processing. Here we demonstrate that high-quality, few-layer BP nanosheets, with controllable size and observable photoluminescence, can be produced in large quantities by liquid phase exfoliation under ambient conditions in solvents such as N-cyclohexyl-2-pyrrolidone (CHP). Nanosheets are surprisingly stable in CHP, probably due to the solvation shell protecting the nanosheets from reacting with water or oxygen. Experiments, supported by simulations, show reactions to occur only at the nanosheet edge, with the rate and extent of the reaction dependent on the water/oxygen content. We demonstrate that liquid-exfoliated BP nanosheets are potentially useful in a range of applications from ultrafast saturable absorbers to gas sensors to fillers for composite reinforcement.
Monitoring of human bodily motion requires wearable sensors that can detect position, velocity and acceleration. They should be cheap, lightweight, mechanically compliant and display reasonable sensitivity at high strains and strain rates. No reported material has simultaneously demonstrated all the above requirements. Here we describe a simple method to infuse liquid-exfoliated graphene into natural rubber to create conducting composites. These materials are excellent strain sensors displaying 104-fold increases in resistance and working at strains exceeding 800%. The sensitivity is reasonably high, with gauge factors of up to 35 observed. More importantly, these sensors can effectively track dynamic strain, working well at vibration frequencies of at least 160 Hz. At 60 Hz, we could monitor strains of at least 6% at strain rates exceeding 6000%/s. We have used these composites as bodily motion sensors, effectively monitoring joint and muscle motion as well and breathing and pulse.
Two-dimensional nanomaterials such as MoS2 are of great interest both because of their novel physical properties and their applications potential. Liquid exfoliation, an important production method, is limited by our inability to quickly and easily measure nanosheet size, thickness or concentration. Here we demonstrate a method to simultaneously determine mean values of these properties from an optical extinction spectrum measured on a liquid dispersion of MoS2 nanosheets. The concentration measurement is based on the size-independence of the low-wavelength extinction coefficient, while the size and thickness measurements rely on the effect of edges and quantum confinement on the optical spectra. The resultant controllability of concentration, size and thickness facilitates the preparation of dispersions with pre-determined properties such as high monolayer-content, leading to first measurement of A-exciton MoS2 luminescence in liquid suspensions. These techniques are general and can be applied to a range of two-dimensional materials including WS2, MoSe2 and WSe2.
In order to fulfill their potential for applications, it will be necessary to develop large-scale production methods for two-dimensional (2D) inorganic nanosheets. Here we demonstrate the large-scale shear-exfoliation of molybdenum disulfide nanosheets in aqueous surfactant solution using a kitchen blender. Using standard procedures, we measure how the MoS2 concentration and production rate scale with processing parameters. However, we also use recently developed methods based on optical spectroscopy to simultaneously measure both nanosheet lateral size and thickness, allowing us to also study the dependence of nanosheet dimensions on processing parameters. We found the nanosheet concentration and production rates to depend sensitively on the mixing parameters (the MoS2 concentration, Ci; the mixing time, t; the liquid volume, V; and the rotor speed, N). By optimizing mixing parameters, we achieved concentrations and production rates as high as 0.4 mg/mL and 1.3 mg/min, respectively. Conversely, the nanosheet size and thickness were largely invariant with these parameters. The nanosheet concentration is also extremely sensitive to the surfactant concentration. However, more interestingly the nanosheet lateral size and thickness also varied strongly with the surfactant concentration. This allows the mean nanosheet dimensions to be controlled during shear exfoliation at least in the range ∼40–220 nm for length and ∼2–12 layers for thickness. We demonstrate the importance of this by showing that the MoS2 nanosheets prepared using different surfactant concentrations, and so displaying different nanosheets sizes, perform differently when used as hydrogen evolution catalysts. We find the nanosheets produced using high surfactant concentrations, which gives smaller flake sizes, perform significantly better, consistent with catalysis occurring at nanosheet edges. Finally, we also demonstrate that shear exfoliation using a kitchen blender is not limited to MoS2 but can also be achieved for boron nitride and tungsten disulfide.
Although transition metal dichalcogenides such as MoS2 have been recognized as highly potent two-dimensional nanomaterials, general methods to chemically functionalize them are scarce. Herein, we demonstrate a functionalization route that results in organic groups bonded to the MoS2 surface via covalent C–S bonds. This is based on lithium intercalation, chemical exfoliation and subsequent quenching of the negative charges residing on the MoS2 by electrophiles such as diazonium salts. Typical degrees of functionalization are 10–20 atom % and are potentially tunable by the choice of intercalation conditions. Significantly, no further defects are introduced, and annealing at 350 °C restores the pristine 2H-MoS2. We show that, unlike both chemically exfoliated and pristine MoS2, the functionalized MoS2 is very well dispersible in anisole, confirming a significant modification of the surface properties by functionalization. DFT calculations show that the grafting of the functional group to the sulfur atoms of (charged) MoS2 is energetically favorable and that S–C bonds are formed.