Sand-gravel mixtures are special engineering geological materials between soils and fractured rocks. This study performs a series of bending element tests to systematically investigate the shear wave velocity (Vs) of the sand-gravel mixtures, establish an effective evaluation method, and assess the influence of relative density and effective confining pressure on mixtures with a wide range of gravel contents. The results showed that the shear wave velocity increases and then decreases with the increase in gravel content and increases with the rise in relative density and effective confining pressure. Furthermore, a shear wave velocity prediction model is proposed in this study based on the intergranular contact state theory, including the stress parameter (n) and skeleton void ratio. The stress parameter can be described by a power function considering the uniformity coefficient. The model serves as a reference guide for estimating the shear wave velocity of sand-gravel mixtures with a wide range of gravel contents.
Vs30 (equivalent shear-wave velocity of soil layers within a depth of 30 m underground) is widely used in the field of seismic engineering; however, due to the limitation of funds, time, measuring devices, and other factors, the depth for testing shear-wave velocity in an engineering site rarely reaches 30 m underground. Therefore, it is necessary to predict Vs30 effectively. We analyzed the existing models using 343 boreholes with depths greater than 30 m in Tangshan, China. It shows that the topographic slope method is not suitable for predicting Vs30 in Tangshan. The Boore (2011) model overestimates, while Boore (2004) underestimates Vs30 in Tangshan, while Junju Xie’s (2016) model has ideal prediction results. We propose three new models in this paper, including the bottom constant velocity (BCV) model, linear model, and conditional independent model. We find that the BCV model has limited prediction ability, and the linear model is more suitable when z ≤ 18 m, while the conditional independent model shows good performance under conditions where z > 18 m. We propose that the model can be accurately and effectively applied in Tangshan and other regions with low shear-wave velocity.
Most of the coastal beach zone in the world is rich in wind energy reserves and has great potential for offshore wind power development. However, the sedimentary environment in the coastal area is complex and changeable, and the nature of the foundation soil of offshore wind power platforms is weak and complex, which is quite different from that in the land areas. In order to systematically study the mechanical properties of marine foundation soils, a series of geotechnical tests are carried out on representative undisturbed seabed soils, such as basic laboratory geotechnical tests, bender element tests, undrained triaxial shear tests, and resonance column tests. The test results show that shear wave velocity (Vs) of marine silt and silty clay increases linearly with the buried depth; the stress‐strain relationship curves of silty clay and silt present two different modes of development: strain hardening and strain softening, the undrained shear strength (Sd) of the two types of marine soils decreases with the increase of the void ratio (e), and both present a good single correlation. Based on the relationship between Sd and Vs from the laboratory test of disturbed seabed soils, an undrained strength evaluation method of undisturbed seabed soils under the current stratum conditions incorporating in situ shear wave velocity is established. The dynamic shear modulus (G) in the various strain ranges of undisturbed silty clay and silt increases regularly with the buried depth (H). Meanwhile, the maximum dynamic shear modulus (Gmax) linearly increases with the increase of H, whereas the attenuation relationship of G decreases with the increase of H. The prediction method of G based on buried depth is established with high accuracy.
Sand-gravel mixtures are typical binary materials, exhibiting highly heterogeneous, discontinuous, and significant structural effects. The contact state between sand and gravel particles has a significant influence on the mechanical properties of the mixtures. This article focused on the complex internal structure and its mesostructural behavior of the mixtures, and a systematic statistical analysis was carried out to study the shape, size, and angularity of the coarse particles. The three-dimensional (3D) shapes of coarse aggregates were approximated to be hexahedron, pentahedron, and tetrahedron. An indicator called angularity and surface texture (AT) index was developed to characterize the combined effect of the coarse aggregate angularity and surface texture. Based on the screening testing and digital image processing, the particle size and AT index of aggregates were extracted, and their means, standard deviations, and statistical distributions were studied. An algorithm for generating 3D aggregates was developed based on the statistical results of the coarse aggregate 3D morphology. The coarse aggregate generating code was written using the fish language in PFC3D. The numerical model was then applied to conduct three typical monotonic or cyclic triaxial test simulations. Retrospective simulation of the laboratory tests using the proposed model showed good agreement, and the reliability of the model is effectively verified. The results interpreted well the mechanism of particle motion and the distribution of interparticle contact force during shearing from mesoscale of the mixtures, which can give better understanding and modeling of the nonlinear behavior of the sand-gravel mixtures.