It is necessary to carry out experiments on cores with different degrees of crack development when studying the seepage law of cracked reservoirs and evaluating cracks. The seepage experiment in the laboratory requires cores with different degrees of microcrack development; cores obtained via conventional drilling cannot meet the requirements, and the efficacies and evaluation methods of geological parameters used for artificial cracks are not perfect. In this study, cores are loaded using a triaxial gripper, and cracks are produced by changing the difference of stress; the relationship between the increased rate of permeability and the change in stress concentration is used to evaluate the degree of development of the crack in real time. The angle between the cracks and the maximum principal stress direction, calculated using the Mohr–Coulomb failure criterion, is 20–27.5°, which provides theoretical support for the process of crack creation. The experimental results show that the permeability variation curve shows two obvious turning points, which divide the whole zone into a reduction zone, a slow increase zone, and a rapid increase zone. Through the obtained experimental and evaluation results, a complete system for crack creation and evaluation is established, which can provide strong support for the study of cracked reservoirs.

The release of dissolved gas during the development of gas-bearing tight oil reservoirs has a great influence on the effect of development. In this article, the high-pressure mercury intrusion experiment was carried out in cores from different regions and lithologies of the Ordos Basin and the Sichuan Basin. The objectives are to study the microscopic characteristics of the porous throat structure of these reservoirs and to analyze the porous flow resistance laws of different lithology by conducting a resistance gradient test experiment. A mathematical model is established and the oil production index is corrected according to the experiment results to predict the oil production. The experimental results show that for tight reservoirs in the same area and lithology, the lower the permeability under the same back pressure, the greater the resistance gradient. And for sandstone reservoirs in different areas, the resistance gradients have little difference and the changes in the resistance coefficients are similar. However, limestone under the same conditions supports a much higher resistance gradient than sandstone reservoirs. Furthermore, the experimental results are consistent with the theoretical analysis indicating that the PVT (pressure–volume-temperature) characteristics in the nanoscale pores are different from those measured in the high-temperature, high-pressure sampler. Only when the pressure is less than a certain value of the bubble point pressure, the dissolved gas will begin to separate and generate resistance. This pressure is lower than the bubble point pressure measured in the high-temperature and pressure sampler. The calculation results show that the heterogeneity of limestone reservoirs and the mismatch of fluid storage and flow space will make the resistance, generated by the separation of dissolved gas, have a greater impact on oil production.

Tight oil reservoirs are characterized by a low porosity, low permeability, and strong heterogeneity. The macropores, throats, and microcracks in reservoirs are the main seepage channels, which affect the seepage law in the reservoirs. In particular, oil-water two-phase flow in different types of pores requires further study. In this study, two groups of online NMR displacement experiments were designed to study the seepage characteristics of tight oil reservoirs. It was found that the main seepage channels for oil-water two-phase flow are the microcracks, large pores, and throats in the reservoir. The large pores are mainly micron and submicron scale in size. The oil in the small pores is only transferred to the large pores through imbibition to participate in the flow, and there is no two-phase flow. Based on the influence of different pore structures on the seepage law of a tight reservoir, the pores were divided into seepage zones, and a multistage seepage model for tight reservoirs was established. Based on this model, the effects of the imbibition, stress sensitivity, threshold pressure gradient, and Jamin effect on model’s yield were studied. The results show that imbibition is no longer effective after a while. Owing to the stress sensitivity, the threshold pressure gradient, and the Jamin effect, oil production will be reduced. As the parameter value increases, the oil production decreases. The production decreases rapidly in the early stage of mining while decreases slowly in the later stage, exhibiting a trend of high yield in the early stage and stable yield in the later stage.

The separation of solution gas has great influence on the development of gas-bearing tight oil reservoirs. In this study, physical simulation and high-pressure mercury intrusion were used to establish a method for determining the porous flow resistance gradient of gas-bearing tight oil reservoirs. A mathematical model suitable for injection–production well networks is established based on the streamline integral method. The concept of pseudo-bubble point pressure is proposed. The experimental results show that as the back pressure decreases from above the bubble point pressure to below the bubble point pressure, the solution gas separates out. During this process, the porous flow resistance gradient is initially equal to the threshold pressure gradient of the oil single-phase fluid, then it becomes relatively small and stable, and finally it increases rapidly and exponentially. The lower the permeability, the higher the pseudo-bubble point pressure, and the higher the resistance gradient under the same back pressure. For tight reservoirs, the production pressure should be maintained above the pseudo-bubble point pressure when the permeability is lower than a certain value. When the permeability is higher than a certain value, the pressure can be reduced below the pseudo-bubble point pressure, and there is a reasonable range. The mathematical results show that after degassing, the oil production rate and the effective utilization coefficient of oil wells decline rapidly. These declines occur later and have a flat trend for high permeability formations, and the production well pressure can be reduced to a lower level. Fracturing can effectively increase the oil production rate after degassing. A formation that cannot be utilized before fracturing because of the blocked throats due to the separation of the solution gas can also be utilized after fracturing. When the production well pressure is lower than the bubble point pressure, which is not too large, the fracturing effect is better.