Arnaud Huijer

Mr. Arnaud Huijer

Delft University of Technology (TU Delft)
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 October 2021 in Sensors
Verified
Journal Article
Open access
PDF file
AHArnaud Huijer
Arnaud Huijer
CKC. Kassapoglou
C. Kassapoglou
LPLotfollah Pahlavan
Lotfollah Pahlavan
Piezoelectric sensors can be embedded in carbon fibre-reinforced plastics (CFRP) for continuous measurement of acoustic emissions (AE) without the sensor being exposed or disrupting hydro- or aerodynamics. Insights into the sensitivity of the embedded sensor are essential for accurate identification of AE sources. Embedded sensors are considered to evoke additional modes of degradation into the composite laminate, accompanied by additional AE. Hence, to monitor CFRPs with embedded sensors, identification of this type of AE is of interest. This study (i) assesses experimentally the performance of embedded sensors for AE measurements, and (ii) investigates AE that emanates from embedded sensor-related degradation. CFRP specimens have been manufactured with and without embedded sensors and tested under four-point bending. AE signals have been recorded by the embedded sensor and two reference surface-bonded sensors. Sensitivity of the embedded sensor has been assessed by comparing centroid frequencies of AE measured using two sizes of embedded sensors. For identification of embedded sensor-induced AE, a hierarchical clustering approach has been implemented based on waveform similarity. It has been confirmed that both types of embedded sensors (7 mm and 20 mm diameter) can measure AE during specimen degradation and final failure. The 7 mm sensor showed higher sensitivity in the 350–450 kHz frequency range. The 20 mm sensor and the reference surface-bounded sensors predominately featured high sensitivity in ranges of 200–300 kHz and 150–350 kHz, respectively. The clustering procedure revealed a type of AE that seems unique to the region of the embedded sensor when under combined in-plane tension and out-of-plane shear stress.

8 August 2024 in Smart Materials and Structures
Verified
Journal Article
Open access
AHArnaud Huijer
Arnaud Huijer
CKChristos Kassapoglou
Christos Kassapoglou
LPLotfollah Pahlavan
Lotfollah Pahlavan
Flexible composite marine propellers can aid the marine industry in reducing carbon emissions and underwater radiated noise pollution. The structural integrity of the blades can be assessed using structural health monitoring. One of these methods is the measurement and analysis of damage-induced acoustic emission signals. This paper experimentally investigates the feasibility of using embedded piezoelectric sensors for the measurement of acoustic emissions throughout a submerged flexible composite marine propeller blade. A full-scale glass-fibre reinforced polymer blade has been manufactured with 24 embedded sensors. While suspended in artificial seawater, acoustic emissions were simulated on the blade. The measurements show that the embedded piezoelectric sensors can measure acoustic emissions while the blade is submerged. Further, the distance from source to sensor over which the acoustic emission is measurable was investigated. For a noise level of 40 dB and a source amplitude of 70 dB between 100 and 250 kHz, an average maximum measurable distance of 124 mm was obtained. For higher frequencies, the distance drops and for lower noise levels the distance increases.

19 May 2022 in Marine Structures
Verified
Journal Article
Open access
AHArnaud Huijer
Arnaud Huijer
XZXiaobo Zhang
Xiaobo Zhang
CKChristos Kassapoglou
Christos Kassapoglou
LPLotfollah Pahlavan
Lotfollah Pahlavan

25 April 2024 in Sensors
Verified
Journal Article
Open access
PDF file
MAM.G.A. Adams
M.G.A. Adams
AHArnaud Huijer
Arnaud Huijer
CKC. Kassapoglou
C. Kassapoglou
JVJohannes Adriaan Arie Vaders
Johannes Adriaan Arie Vaders
LPLotfollah Pahlavan
Lotfollah Pahlavan
The multimodal and dispersive character of ultrasonic guided waves (UGW) offers the potential for non-destructive evaluation of fiber-reinforced composite (FRC) materials. In this study, a methodology for in situ stiffness assessment of FRCs using UGWs is introduced. The proposed methodology involves a comparison between measured wave speeds of the fundamental symmetric and antisymmetric guided wave modes with a pre-established dataset of UGW speeds and translation of them to corresponding stiffness properties, i.e., ABD-components, in an inverse manner. The dispersion relations of guided waves have been calculated using the semi-analytical finite element method. First, the performance of the proposed methodology has been assessed numerically. It has been demonstrated that each of the independent ABD-components of the considered laminate can be approximated with an error lower than 10.4% compared to its actual value. The extensional and bending stiffness properties can be approximated within an average error of 3.6% and 9.0%, respectively. Secondly, the performance of the proposed methodology has been assessed experimentally. This experimental assessment has been performed on a glass fiber-reinforced composite plate and the results were compared to mechanical tensile and four-point bending tests on coupons cut from the plate. Larger differences between the estimated ABD-components according to UGW and mechanical testing were observed. These differences were partly attributed to the variation in material properties across the test plate and the averaging of properties over the measurement area.

22 June 2022
Verified
Book Chapter
Closed access
PDF file
AHArnaud Huijer
Arnaud Huijer
CKChristos Kassapoglou
Christos Kassapoglou
LPLotfollah Pahlavan
Lotfollah Pahlavan