C. Kassapoglou

Dr. C. Kassapoglou


Research Focus & Metrics

Academic Career Length

37Years (1990-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 October 2021 in Sensors
Verified
Journal Article
Open access
PDF file
AHArnaud Huijer
Arnaud Huijer
CKC. Kassapoglou
C. Kassapoglou
LPLotfollah Pahlavan
Lotfollah Pahlavan
Piezoelectric sensors can be embedded in carbon fibre-reinforced plastics (CFRP) for continuous measurement of acoustic emissions (AE) without the sensor being exposed or disrupting hydro- or aerodynamics. Insights into the sensitivity of the embedded sensor are essential for accurate identification of AE sources. Embedded sensors are considered to evoke additional modes of degradation into the composite laminate, accompanied by additional AE. Hence, to monitor CFRPs with embedded sensors, identification of this type of AE is of interest. This study (i) assesses experimentally the performance of embedded sensors for AE measurements, and (ii) investigates AE that emanates from embedded sensor-related degradation. CFRP specimens have been manufactured with and without embedded sensors and tested under four-point bending. AE signals have been recorded by the embedded sensor and two reference surface-bonded sensors. Sensitivity of the embedded sensor has been assessed by comparing centroid frequencies of AE measured using two sizes of embedded sensors. For identification of embedded sensor-induced AE, a hierarchical clustering approach has been implemented based on waveform similarity. It has been confirmed that both types of embedded sensors (7 mm and 20 mm diameter) can measure AE during specimen degradation and final failure. The 7 mm sensor showed higher sensitivity in the 350–450 kHz frequency range. The 20 mm sensor and the reference surface-bounded sensors predominately featured high sensitivity in ranges of 200–300 kHz and 150–350 kHz, respectively. The clustering procedure revealed a type of AE that seems unique to the region of the embedded sensor when under combined in-plane tension and out-of-plane shear stress.

19 October 2024 in Composites Part B: Engineering
Verified
Journal Article
Open access
SPSiddharth Pantoji
Siddharth Pantoji
CKC. Kassapoglou
C. Kassapoglou
DPDaniël Peeters
Daniël Peeters

1 October 2017 in Composites Part A: Applied Science and Manufacturing
Verified
Journal Article
Closed access
WZWeiling Zheng
Weiling Zheng
CKC. Kassapoglou
C. Kassapoglou

26 November 2024 in Composite Structures
Verified
Journal Article
Open access
NHNiels van Hoorn
Niels van Hoorn
STSergio Turteltaub
Sergio Turteltaub
CKC. Kassapoglou
C. Kassapoglou
WBWouter vd Brink
Wouter vd Brink

31 July 2018 in CEAS Aeronautical Journal
Verified
Journal Article
Open access
PDF file
GMGunther Moors
Gunther Moors
CKC. Kassapoglou
C. Kassapoglou
SASergio Frascino Müller de Almeida
Sergio Frascino Müller de Almeida
CFClovis Augusto Eça Ferreira
Clovis Augusto Eça Ferreira
A process to efficiently design composite wing boxes is presented. It uses analytical and semi-empirical equations for failure modes such as material strength, plate buckling, stiffener column buckling and stiffener flange or web crippling. Laminate layups for the different components are selected in accordance with basic engineering rules and guidelines and are updated as necessary to meet the local loads. The emphasis is in allowing buckling of skins at any fraction of the ultimate load and allowing local load redistribution from buckled to non-buckled panels to save weight. The design process is automated and the design can be automatically transferred over to a commercial finite-element code for detailed design and validation. The effects on weight of number of spars, ribs, and stiffeners as well as the fraction of ultimate load at which buckling is allowed are examined and insight is gained to which of these the weight is most sensitive to. In addition, the effect of minimum gage on weight was found to be a driver.

28 July 2016 in Journal of Composite Materials
Verified
Journal Article
Closed access
CKC. Kassapoglou
C. Kassapoglou
An approach to predict static and fatigue failure of composite laminates with holes is presented. Static failure is predicted when the stress averaged over a characteristic distance is equal to the un-notched failure strength. This averaging distance is determined analytically without the use of additional testing or need for extra material parameters. During fatigue loading, the size of the damage region next to the hole is calculated and the strains at the hole edge are determined. These are used along with the stresses just outside the damage region to determine whether failure starts at the hole edge or the edge of the damage region extends. A previously developed fatigue model based on the cycle-by-cycle probability of failure is used to calculate the number of cycles needed for the residual strain at hole edge or the residual strength at the edge of the damage region to fall below the corresponding applied values. The procedure is repeated until laminate failure. The method is also used to predict cycles to failure for impacted specimens. The predictions are in very good agreement with test results.