Lotfollah Pahlavan

Dr. Lotfollah Pahlavan

orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 October 2021 in Sensors
Verified
Journal Article
Open access
PDF file
AHArnaud Huijer
Arnaud Huijer
CKC. Kassapoglou
C. Kassapoglou
LPLotfollah Pahlavan
Lotfollah Pahlavan
Piezoelectric sensors can be embedded in carbon fibre-reinforced plastics (CFRP) for continuous measurement of acoustic emissions (AE) without the sensor being exposed or disrupting hydro- or aerodynamics. Insights into the sensitivity of the embedded sensor are essential for accurate identification of AE sources. Embedded sensors are considered to evoke additional modes of degradation into the composite laminate, accompanied by additional AE. Hence, to monitor CFRPs with embedded sensors, identification of this type of AE is of interest. This study (i) assesses experimentally the performance of embedded sensors for AE measurements, and (ii) investigates AE that emanates from embedded sensor-related degradation. CFRP specimens have been manufactured with and without embedded sensors and tested under four-point bending. AE signals have been recorded by the embedded sensor and two reference surface-bonded sensors. Sensitivity of the embedded sensor has been assessed by comparing centroid frequencies of AE measured using two sizes of embedded sensors. For identification of embedded sensor-induced AE, a hierarchical clustering approach has been implemented based on waveform similarity. It has been confirmed that both types of embedded sensors (7 mm and 20 mm diameter) can measure AE during specimen degradation and final failure. The 7 mm sensor showed higher sensitivity in the 350–450 kHz frequency range. The 20 mm sensor and the reference surface-bounded sensors predominately featured high sensitivity in ranges of 200–300 kHz and 150–350 kHz, respectively. The clustering procedure revealed a type of AE that seems unique to the region of the embedded sensor when under combined in-plane tension and out-of-plane shear stress.

23 December 2022 in Sensors
Verified
Journal Article
Open access
PDF file
SASarjoon Alkhateeb
Sarjoon Alkhateeb
FRFilippo Riccioli
Filippo Riccioli
FMFelipe Leon Morales
Felipe Leon Morales
LPLotfollah Pahlavan
Lotfollah Pahlavan
Offshore support structures and mooring systems are predominantly subject to corrosion and fatigue. These structures are typically covered with marine growth of various types. Conventional inspection methods for assessment of the structural integrity require access to the cleaned surface of these structures; however, the cleaning process is highly undesirable from the technical, economical, and environmental points of view. This paper highlights research on feasibility assessment of detection and localization of corrosion damage under marine growth using acoustic emission (AE). Experiments were conducted on two carbon steel plates, one baseline sample and one covered with artificially fabricated marine growth. The results of accelerated corrosion experiments suggest that corrosion-induced ultrasound signals can be detected with satisfactory signal-to-noise ratio using non-contact AE sensors. Ultrasound waves passing through marine growth showed around 12 dB drop in amplitude when compared to the base plate. A localization algorithm for corrosion induced-ultrasound signals was successfully implemented.

16 February 2022 in Sensors
Verified
Journal Article
Open access
PDF file
BSBart Scheeren
Bart Scheeren
MKMiroslaw Lech Kaminski
Miroslaw Lech Kaminski
LPLotfollah Pahlavan
Lotfollah Pahlavan
In the condition monitoring of bearings using acoustic emission (AE), the restriction to solely instrument one of the two rings is generally considered a limitation for detecting signals originating from defects on the opposing non-instrumented ring or its interface with the rollers due to the signal energy loss. This paper presents an approach to evaluate transmission in low-speed roller bearings for application in passive ultrasound monitoring. An analytical framework to describe the propagation and transmission of ultrasonic waves through the geometry and interfaces of a bearing is presented. This framework has been used to evaluate the transmission of simulated damage signals in an experiment with a static bearing. The results suggest that low- to mid-frequency signals (<200 kHz), when passing through the rollers and their interfaces from one raceway to the other, can retain enough energy to be potentially detected. An average transmission loss in the range of 10–15 dB per interface was experimentally observed.

25 April 2024 in Sensors
Verified
Journal Article
Open access
PDF file
MAM.G.A. Adams
M.G.A. Adams
AHArnaud Huijer
Arnaud Huijer
CKC. Kassapoglou
C. Kassapoglou
JVJohannes Adriaan Arie Vaders
Johannes Adriaan Arie Vaders
LPLotfollah Pahlavan
Lotfollah Pahlavan
The multimodal and dispersive character of ultrasonic guided waves (UGW) offers the potential for non-destructive evaluation of fiber-reinforced composite (FRC) materials. In this study, a methodology for in situ stiffness assessment of FRCs using UGWs is introduced. The proposed methodology involves a comparison between measured wave speeds of the fundamental symmetric and antisymmetric guided wave modes with a pre-established dataset of UGW speeds and translation of them to corresponding stiffness properties, i.e., ABD-components, in an inverse manner. The dispersion relations of guided waves have been calculated using the semi-analytical finite element method. First, the performance of the proposed methodology has been assessed numerically. It has been demonstrated that each of the independent ABD-components of the considered laminate can be approximated with an error lower than 10.4% compared to its actual value. The extensional and bending stiffness properties can be approximated within an average error of 3.6% and 9.0%, respectively. Secondly, the performance of the proposed methodology has been assessed experimentally. This experimental assessment has been performed on a glass fiber-reinforced composite plate and the results were compared to mechanical tensile and four-point bending tests on coupons cut from the plate. Larger differences between the estimated ABD-components according to UGW and mechanical testing were observed. These differences were partly attributed to the variation in material properties across the test plate and the averaging of properties over the measurement area.

17 May 2012 in Philosophical Magazine
Verified
Journal Article
Closed access
LPLotfollah Pahlavan
Lotfollah Pahlavan
CKC. Kassapoglou
C. Kassapoglou
ASA.S.J. Suiker
A.S.J. Suiker
ZGZ. Gürdal
Z. Gürdal

Verified
Journal Article
Open access
PDF file
EKElyas Mirzaee Kakhki
Elyas Mirzaee Kakhki
JRJalil Rezaeepazhand
Jalil Rezaeepazhand
FDFabian Duvigneau
Fabian Duvigneau
LPLotfollah Pahlavan
Lotfollah Pahlavan
RMResam Makvandi
Resam Makvandi
Sascha EisenträgerSascha Eisenträger
Sascha Eisenträger
In this research, high-order shape functions commonly used in different finite element implementations are investigated with a special focus on their applicability in the semi-analytical finite element (SAFE) method being applied to wave propagation problems. Hierarchical shape functions (p-version of the finite element method), Lagrange polynomials defined over non-equidistant nodes (spectral element method), and non-uniform rational B-splines (isogeometric analysis) are implemented in an in-house SAFE code, along with different refinement strategies such as h-, p-, and k-refinement. Since the numerical analysis of wave propagation is computationally quite challenging, high-order shape functions and local mesh refinement techniques are required to increase the accuracy of the solution, while at the same time decreasing the computational costs. The obtained results reveal that employing a suitable high-order basis in combination with one of the mentioned mesh refinement techniques has a notable effect on the performance of the SAFE method. This point becomes especially beneficial when dealing with applications in the areas of structural health monitoring or material property identification, where a model problem has to be solved repeatedly.